Barco R9000977, R9000972 installation manual Switching on the projector, Fuses

Page 22

 

 

 

AC power connection

 

 

 

 

Fuses

 

 

 

Warning !

 

 

 

For continued protection against fire hazard :

AC power

Fuses

Order Number

Replace with the same type of fuse.

230 Vac

T6.3A/250V (2x)

R314145

Refer replacement to qualified service personnel.

120 Vac

T10A/250V (2x)

R314154

 

 

 

 

Switching on the projector

The projector is switched ON and OFF using the power (mains) switch ON/OFF.

If the switch is pressed in

: ON

If the switch is Not pressed in : OFF

The projector can be started up in the 'Operational mode' (image displayed) or in the 'Stand-by mode', depending on the position of the 'Power-up' DIP switch on the controller board. This DIP switch is set during installation by a qualified technician. If you want to change this start up mode, call a qualified technician.

Power indication lamp :

OFF : no power.

Green : projector in operational mode.

Red : projector in stand-by mode.

When switching on the projector, with the power switch or via the stand-by key on the RCU, the projector can start up in two ways if the "CRT run in cycle" option is switched OFF :

A full white image (projector warm up) or

Immediately image display.

The way of starting up can be set in the service mode.

Starting up with a full white image

When the projector is set to start up with a full white image, the "Projector warm up" menu will be displayed for 30 seconds.

Start up with "Warm up period"

If no action is taken, a white image will be displayed for 20 minutes. This white image will be shifted on the faceplate of the CRT to avoid a CRT burn-in.

It is also possible to adjust the dimensions fo that white image to avoid scanning on the edges of the CRT's. Push the control disk up or down to adjust the vertical amplitude and push the control disk to the right or to the left to adjust the horizontal amplitude.

During this warm up period, it is possible to interrupt this white image projection by pressing EXIT. The "Projector warm up" menu will be re-displayed for another 30 seconds but with the remaining time indicated.

If EXIT is pressed again, the remaining warm up period will be skipped.

During the warm up period, every 30 seconds a text box with the remaining time will be displayed on the screen for 2 seconds. This text box will be displayed every time on another place to avoid a CRT burn-in.

PROJECTOR WARM UP

A FULL WHITH PATTERN WILL BE GENERATED FOR 20 MINUTES

FOR IMMEDIATE USE OF THE PROJECTOR, PRESS <EXIT>

WARNING : SKIPPING THIS PROCEDURE CAN REDUCE QUALITY OF THE PROJECTED IMAGE.

THIS OPTION CAN BE

DISABLED IN THE SERVICE

MENU

REMAINING PROJECTOR WARM UP TIME

18.5 MIN

PLEASE USE <EXIT> TO LEAVE THIS PROCEDURE

5975638 BARCOGRAPHICS 1209s 010797

 

6-3

 

Image 22
Contents Installation Manual Barco Projection Systems Page Safety Instructions Installation Adjustment Mode OWNER’SRECORD Safety InstructionsInstallation Instructions Part Number SER. Number DealerOn installation Contents of the shipping carton Unpacking and Projector DimensionsUnpacking Projector dimensions in mm What about ambient light ? Installation GuidelinesEnvironment Which screen type?Where to install the projector ? Mounting ConfigurationRe-installing the top cover Installation SET-UPAccess to Controls Opening the top coverGaining access to the scan switches Scan Adaptation5HDUFHLOLQJ Hduwdeo HGraphics 1209s Password Mode Power UP Mode Projector SET-UPSetting the projector address OFF onStand-By mode Power-up modeOperational mode Baud Rate for communication with a computerPassword mode Preparing your power cord AC Power ConnectionAC Power mains cord connection Mains lead power cord with CEE7 plugAC Power check AC Input power mains voltage adaptationSwitching on the projector FusesStart up without Warm up period Termination Switch for Video Signal input connectionConnecting a Composite Video source to Port Source ConnectionsTermination Switch for S-video Connecting a S-Video or Composite Video source to PortConnecting a RGB Analog source to Port RED Green BlueConnecting a RGB Analog source to Port 4/5 Connecting a Component Video source to Port 4/5Connecting an IR Remote Receiver 800 to the projector Connecting a Rcvds 05 source selector to the projectorConnecting a VS05 source selector to the projector Peripheral equipmentOverview flowchart of the Installation Adjustment Mode Access to Installation Adjustment ModeEnter Optical Lens Focusing Projector DistanceZurqjudvwhusrvlwlrq Raster CenteringCRT Projection Angle Adjustment CRT Projection Angle AdjustmentCRT Scheimpflug Adjustment Diagonal image focusing Green RED BlueEROW$ LensInstallation adjustment mode Barco Ceiling Mount Support Exploded view of Barco ceiling mount SupportWater-level adjustment Projector axis adjustment Projector-position correctionsG2 Adjustment $-867017Appendix B G2 adjustment Gamma Corrections Gamma CorrectionsFactory Preset Chemical Name and Synonyms Trade Name and Synonyms Federal Stock Number FSN Gross Weight LBSEmergencyphoneno Chemical Family FormulaTreshold Limit Value Precautions to be Taken in Handling and StoringOther Precautions Waste Disposal Method Spill
Related manuals
Manual 60 pages 34.74 Kb

R9000972, R9000977 specifications

Barco, a leader in visualization technology, has made significant strides with its R9000977 and R9000972 projectors, designed primarily for professional applications in various sectors such as broadcasting, events, corporate, and health care. These models showcase exceptional performance coupled with advanced features and cutting-edge technology to deliver consistent, high-quality projections.

The Barco R9000977 is celebrated for its impressive brightness, reaching up to 20,000 lumens, which allows it to operate effectively in both dark and well-lit environments. This projector utilizes a powerful laser light source combined with Barco's laser phosphor technology. This combination not only enhances brightness but also extends the longevity of the projector, making it a cost-effective choice for long-term use.

On the other hand, the R9000972, while slightly lower in lumens at around 15,000, still provides exceptional image quality. Both models support high resolution, often up to 4K or even beyond, ensuring crisp and clear visuals. They leverage advanced imaging technologies such as DLP and proprietary color management systems to provide stunning color accuracy and contrast, crucial for professional presentations and cinematic experiences.

A key characteristic of these projectors is their versatility; they come equipped with a range of connectivity options, including HDMI, SDI, and DisplayPort, enabling seamless integration into existing AV setups. Additionally, they offer flexible lens options, so users can tailor the projector to their space's specific requirements, whether for large venues or more intimate setups.

User-friendliness is another essential aspect of Barco projectors. Features such as intuitive interfaces, built-in presets, and advanced control options simplify the setup and management processes. Furthermore, both models are designed with maintenance in mind, featuring accessible filters and advanced cooling systems to prolong hardware life and ensure consistent performance.

In a world increasingly reliant on high-quality visual displays, the Barco R9000977 and R9000972 projectors stand out due to their advanced technology, versatility, and high performance. Whether used for large events, corporate functions, or educational purposes, these projectors embody Barco's commitment to innovation and excellence in the field of visualization.