Barco R9000972, R9000977 Connecting a S-Video or Composite Video source to Port, RED Green Blue

Page 25

Source connections

Connecting a S-Video (or Composite Video) source to Port 2

Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals can be connected to Port 2 . A composite video signal can also be connected to this port.

To select the S-video input :

Press the digit button 2 on the RCU or the local keypad.

In case of using Port 2 for connecting the Composite Video, the selection of this source have to be done inside the "Picture Tuning" menu. Please refer to the Owner's Manual.

75 W Termination Switch for S-video

Terminate the S-video input of the projector using the 75 switch next to the S-video input when the projector operates alone or when the projector is the last unit in a loop-through configuration.

The switch is set to "ON" : signal terminated.

The switch is set to "OFF": signal not terminated.

4 pin connector configurations:

For S-video:

 

For video:

Pin 1: earth(ground) luminance

 

Pin 1:

earth(ground) video

Pin 2: earth(ground) chrominance

3

Pin 2:

notconnected

Pin 3: luminance signal(Y)

1

Pin :

video signal

 

1Vpp± 3dB

2

Pin 4: notconnected

Pin 4: chrominance signal(C)

4

 

 

 

 

 

300mVpp± 3dB

 

 

 

75Termination

Switch

Connecting a RGB Analog source to Port 3

Connect a RGB Analog signal via an interface (e.g. RGB 120MHz interface, part number 98 26570) to Port 3. RGB analog input with automatic sync detection (Separate H and V sync inputs, with composite sync input or with sync signals on green) and automatic polarity detection.

Pin configuration of the D9 (male) connector of the Analog input :

1not connected

2 ground RGBS

3RED

4GREEN

5BLUE

6ground RGBS

7 ground RGBS

8 Horizontal /composite sync

9 Vertical sync

To select the RGB analog Input :

Press the digit button 3 on the RCU or the local keypad.

RGB 120MHz interface

361

Locations of the Termination Resistors and Switches on the RGB Input Auto Sync Tracking Module

When changing a switch position or removing a resistor, turn off the projector and unplug the power cord from the wall outlet.

75 W Termination resistors

In case of chaining (loop-through) the projectors, the 75line termination resistors must be removed from the RGB Input Auto Sync Tracking Module when the projector is NOT the last unit in the chain. In case of a stand-alone projector, do not remove the resistors.

75

resistors on the module :

line terminated.

75

resistors removed

:

line not terminated.

S2 Blue in Green (ON=yes)

R101

 

 

 

Vsync

R81

 

 

 

 

 

 

Hsync R41

R21

 

 

(Blue)

S1 Force Negative Sync

 

 

(Green) R1

(ON=yes)

 

 

(Red)

 

Line termination 75 resistors

7-2

 

5975638 BARCOGRAPHICS 1209s 010797

 

Image 25
Contents Installation Manual Barco Projection Systems Page Safety Instructions Installation Adjustment Mode Installation Instructions Safety InstructionsOWNER’SRECORD Part Number SER. Number DealerOn installation Contents of the shipping carton Unpacking and Projector DimensionsUnpacking Projector dimensions in mm Environment Installation GuidelinesWhat about ambient light ? Which screen type?Mounting Configuration Where to install the projector ?Access to Controls Installation SET-UPRe-installing the top cover Opening the top coverScan Adaptation Gaining access to the scan switchesHduwdeo H 5HDUFHLOLQJGraphics 1209s Projector SET-UP Password Mode Power UP ModeOFF on Setting the projector addressOperational mode Power-up modeStand-By mode Baud Rate for communication with a computerPassword mode AC Power mains cord connection AC Power ConnectionPreparing your power cord Mains lead power cord with CEE7 plugAC Input power mains voltage adaptation AC Power checkFuses Switching on the projectorStart up without Warm up period Connecting a Composite Video source to Port Signal input connectionTermination Switch for Video Source ConnectionsConnecting a RGB Analog source to Port Connecting a S-Video or Composite Video source to PortTermination Switch for S-video RED Green BlueConnecting a Component Video source to Port 4/5 Connecting a RGB Analog source to Port 4/5Connecting a VS05 source selector to the projector Connecting a Rcvds 05 source selector to the projectorConnecting an IR Remote Receiver 800 to the projector Peripheral equipmentOverview flowchart of the Installation Adjustment Mode Access to Installation Adjustment ModeEnter Projector Distance Optical Lens FocusingRaster Centering ZurqjudvwhusrvlwlrqCRT Projection Angle Adjustment CRT Projection Angle AdjustmentCRT Green RED Blue Scheimpflug Adjustment Diagonal image focusingLens EROW$Installation adjustment mode Exploded view of Barco ceiling mount Support Barco Ceiling Mount SupportProjector-position corrections Water-level adjustment Projector axis adjustment$-867017 G2 AdjustmentAppendix B G2 adjustment Gamma Corrections Gamma CorrectionsFactory Preset Emergencyphoneno Federal Stock Number FSN Gross Weight LBSChemical Name and Synonyms Trade Name and Synonyms Chemical Family FormulaOther Precautions Precautions to be Taken in Handling and StoringTreshold Limit Value Waste Disposal Method Spill
Related manuals
Manual 60 pages 34.74 Kb

R9000972, R9000977 specifications

Barco, a leader in visualization technology, has made significant strides with its R9000977 and R9000972 projectors, designed primarily for professional applications in various sectors such as broadcasting, events, corporate, and health care. These models showcase exceptional performance coupled with advanced features and cutting-edge technology to deliver consistent, high-quality projections.

The Barco R9000977 is celebrated for its impressive brightness, reaching up to 20,000 lumens, which allows it to operate effectively in both dark and well-lit environments. This projector utilizes a powerful laser light source combined with Barco's laser phosphor technology. This combination not only enhances brightness but also extends the longevity of the projector, making it a cost-effective choice for long-term use.

On the other hand, the R9000972, while slightly lower in lumens at around 15,000, still provides exceptional image quality. Both models support high resolution, often up to 4K or even beyond, ensuring crisp and clear visuals. They leverage advanced imaging technologies such as DLP and proprietary color management systems to provide stunning color accuracy and contrast, crucial for professional presentations and cinematic experiences.

A key characteristic of these projectors is their versatility; they come equipped with a range of connectivity options, including HDMI, SDI, and DisplayPort, enabling seamless integration into existing AV setups. Additionally, they offer flexible lens options, so users can tailor the projector to their space's specific requirements, whether for large venues or more intimate setups.

User-friendliness is another essential aspect of Barco projectors. Features such as intuitive interfaces, built-in presets, and advanced control options simplify the setup and management processes. Furthermore, both models are designed with maintenance in mind, featuring accessible filters and advanced cooling systems to prolong hardware life and ensure consistent performance.

In a world increasingly reliant on high-quality visual displays, the Barco R9000977 and R9000972 projectors stand out due to their advanced technology, versatility, and high performance. Whether used for large events, corporate functions, or educational purposes, these projectors embody Barco's commitment to innovation and excellence in the field of visualization.