Proxima ASA Pro AV 9400 manual Lamp Replacement Indicator, Lamp Cover Lamp Assembly Handle

Page 54

APPENDIX

LAMP REPLACEMENT

When the Projection Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow and the warning message "LAMP REPLACEMENT" appears as the right figure. When the warning message is displayed, the Projection Lamp should be replaced.

To terminate the warning message.

Replace the Projection Lamp and reset the LAMP REPLACEMENT MONITOR TIMER (See "LAMP AGE" section on page 52.), and the warning message is terminated.

LAMP REPLACEMENT INDICATOR

To erase the warning message in a moment.

LAMP REPLACEMENT

To erase the warning message for a moment, move the arrow to "YES" by pressing the POINT UP/DOWN BUTTON(s) and then press the SELECT (REAR CLICK) BUTTON. This procedure is temporary measure, and the warning massage appears again when the projector is turned on next time.

●For continued safety, replace with a lamp assembly of the same type.

● Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot.

●Do not drop the lamp module or touch the glass bulb ! The glass can shatter and cause injury.

Follow these steps to replace the lamp assembly.

1.Turn off the projector and allow the projector to cool thoroughly.

2.Disconnect the AC cord from the projector.

3.Remove 2 screws with a screwdriver and disconnect the lamp cover.

4.Remove 2 screws with a screwdriver and pull out the lamp assembly by grasping the handle.

5.Replace the lamp assembly.

6.Tighten 4 screws to secure the lamp cover to the lamp assembly.

7.Connect the detachable AC cord to the projector.

8.Reset the lamp replacement monitor timer.

(See "LAMP AGE" section on page 52.)

NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER, except after the lamp is replaced.

LAMP

COVER

LAMP ASSEMBLY

HANDLE

NOTE ON THE LAMP REPLACEMENT INDICATOR AND MESSAGE

The LAMP REPLACEMENT INDICATOR and the warning message "LAMP REPLACEMENT" indicates the guide of the lamp life.

It is unnecessary to replace the lamp immediately if the projector is operating normally with the indicator on.

If the LAMP REPLACE INDICATOR is lit (and warning message "LAMP REPLACEMENT" is displayed on the screen) and the power is not be turned on by pressing the power button (Power is turned off approximately 20 seconds after power button is pressed.), the lamp replacement is required. Please contact a service for the lamp replacement.

54

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Multimedia Projector Model Pro AV Pro AV 9400L Without Lens To the Owner Important Safety Instructions Table of Contents Features and Design Front of the Projector InstallationName of Each Part of the Projector Rear of the ProjectorPositioning SETTING-UP the ProjectorLeveling and Elevating Adjustments Room LightMoving the Projector VentilationExhaust Vent AIR Intake Ventrear Side Bottom Side Power Requirements Projector side Female AC outlet side MaleConnecting the Projector Terminal of the ProjectorSide of the Projector Connect the Computer Video Input JACK-2 Side of the Projector Connect the Video EquipmentVideo Input JACK-1 Video Monitor S-VIDEO Output JackConnecting to the Computer Input 1 Terminal MDR20 Digital Connecting the ComputerConnecting to the Computer Input 1 Terminal HDB15 Analog Control Port Cable Removal HintConnecting to the Serial Port DB9-PIN Terminal Connecting to the Monitor Output Terminal HDB15Connecting to the Audio Monitor Output Variable Jacks HDB 15-PIN TerminalInput Monitor Cable Connecting AN IBM-COMPATIBLE Laptop Computer Before using with digital connection, install Connecting a Macintosh Desktop Computer ComputerAnalog Connecting a Macintosh Powerbook Computer Connecting the Video Equipment Connecting to the S-VHS Video Monitor Output JackConnecting the Video Equipment Video EquipmentFront Indicators TOP Controls Controls and IndicatorsFront Indicators Before OperationReady Indicator Lamp Replacement IndicatorTemperature Warning Indicator Lamp Power IndicatorOperation of the Remote Control Wireless Remote Control UnitLaser Light Window Video Select Button Timer ButtonComputer Select Button Zoom ButtonRemote Control Battery Installation 1714 Using the Remote Control Unit wireless Wired Remote CableControl the Projector Direct OperationCOMPUTER/VIDEO Mode Video ModeMenu Operation Computer Mode Picture PositionTo Turn on the Projector Basic OperationTurning ON/OFF the Projector To Turn OFF the ProjectorDirect Operation Normal Picture Function Timer FunctionDigital Zoom Function Freeze Picture FunctionMenu Operation Sound Adjustment Language AdjustmentVideo Source Select Video ModeColor System Select Main Menu Display Color SystemPicture Image Adgustment Picture Screen Adjustment Main Menu Display Screen AdjustComputer System Display Current Mode Computer ModePC Adjustment Computer System SelectCompatible Computer Specifications Main Menu Display Auto Image Setting Decrease Increase Picture Image AdjustmentMain Menu Display Image Adjust Lighter DeeperPicture Position Adjustment Main Menu Display Position SettingPC Adjustment Main Menu Display PC Adjustment OK ?PC Adjustment Display Mode Free Picture Screen Adjustment Other Function Setting Blue Back On or OffRemote Control Mode 1 or Mode Main Menu Display SettingLamp AGE Appendix Temperature Warning IndicatorAIR Filter Care and Cleaning MeintenanceLamp Replacement Lamp Replacement IndicatorLamp Cover Lamp Assembly Handle Troubleshooting Cleaning the LensNo sound FAXTechnical Specifications AV Input JacksWarranty
Top Page Image Contents