Proxima ASA DP9270 manual Turning on / OFF Projector, Turning on Projector, Turning OFF Projector

Page 19

BEFORE OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

1

Complete peripheral connections (with Computer, VCR, etc.)

before turning on projector. (Refer to "CONNECTING TO

 

PROJECTOR" on pages 11~13 for connecting that equipment.)

2

Connect a projector's AC Power Cord into an AC outlet. LAMP

Indicator lights RED, and READY Indicator lights GREEN.

 

NOTE : When “On start” function is ON, this projector is turned

 

on automatically by connecting AC Power Cord to an

 

AC outlet. (Refer to pages 35, 36.)

3

Press POWER ON-OFF button on Top Control or on Remote

Control Unit to ON. LAMP Indicator dims, and Cooling Fans

start to operate. Preparation Display appears on a screen and count-down starts. Signal from PC or Video source appears after 30 seconds.

30

Preparation Display disappears after 30 seconds.

E

TURNING OFF PROJECTOR

1

Press POWER ON-OFF button on Top Control or on Remote

Control Unit, and a message "Power off?" appears on a screen.

2

Press POWER ON-OFF button again to turn off projector. LAMP

Indicator lights bright and READY Indicator turns off. After

 

projector is turned off, Cooling Fans operate (for 90 seconds).

 

During this "Cooling Down" period, this appliance cannot be

 

turned on.

3

When projector has cooled down, READY Indicator lights

GREEN again and you can turn projector on. After cooling down

completely, disconnect AC Power Cord.

TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

Power off?

Message disappears after 4 seconds.

When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on pages 35 and 36.

When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again.

When WARNING TEMP. Indicator continues to flash, follow procedures below:

1.Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet.

2.Check Air Filters for dust accumulation.

3.Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.)

4.Turn a projector on again.

If WARNING TEMP. Indicator should still continue to flash, contact sales dealer where you purchased this projector or service center.

19

Image 19
Contents Draft To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Component Video Features and DesignComputers Color SystemsName of Each Part of Projector Preparation200 240 V AC SETTING-UP ProjectorConnecting AC Power Cord For U.S.A. and Canada For Continental EuropeRoom Light Preparation Positioning ProjectorMoving Projector Preparation Adjustable FeetBNC Input Jacks Connecting ProjectorTerminals of Projector Audio Input JacksTerminals A Projector Connecting to ComputerAudio Video Connecting to Video EquipmentBefore Operation Operation of Remote ControlLaser Pointer Function Focus Button Volume ButtonWired Remote Jack Zoom ButtonReady Indicator TOP Controls and IndicatorsOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARSound Menu Turning on Projector Turning on / OFF ProjectorTurning OFF Projector Keystone Adjustment Adjusting ScreenFocus Adjustment Lens Shift AdjustmentSound Adjustment Input Computer InputSelecting Input Source Selecting Computer SystemAuto PC AdjustmentAuto PC Adjustment Computer Input Automatic MULTI-SCAN SystemComputer Input Manual PC Adjustment Full screen Computer InputDisplay area Display area H1024 x 48.363 60.004 Computer Input Compatible Computer SpecificationsResolution 640 x 31.469 59.940Image 1~4 Picture Image AdjustmentsImage Level Select Direct Image Level Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentSource Select Menu Video Video InputVideo Pb/Cb,Pr/CrPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N Component Video Signal FormatSelecting Video System Video InputImage button Standard Cinema CinemaVideo Input Image Level Adjustment Closes Image Menu Reset Reset all adjustment to previous figure QuitSetting Menu SettingSetting Menu To change code of Projector To change code of Remote Control UnitOperating Wireless Mouse SETTING/APPENDIXOperating Wireless Mouse InstallationAIR Filter Care and Cleaning MaintenanceCleaning Projection Lens Lamp Replace Counter Appendix Lamp ReplacementTroubleshooting Function does not Remote Control UnitWireless Mouse Does not workTechnical Specifications USB Connector Series B Appendix Configurations of TerminalsWarranty Deutsch D 2001 610 295 1424 1AA6P1P2972-- MB8F