Onkyo TX-NR579 Connecting the AV Receiver, Connecting Your Speakers, Screw-type speaker terminals

Page 11

Connecting the AV Receiver

Connecting Your Speakers

Connecting the Speaker Cables

The following illustration shows which speaker should be connected to each pair of terminals. If you’re using only one surround back speaker, connect it to the SURROUND BACK or FRONT HIGH L terminals.

Surround

Center

right

left

Surround back/	Surround back/	Front right	Front left
Front high	Front high
right	left

Tip

•You can specify whether surround back or front high speakers are connected in the “Speaker Configuration” menu (➔ page 43) or during Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 29).

■Screw-type speaker terminals

	Strip 12 to 15 mm of insulation from the ends of the	12 to 15 mm
	speaker cables, and twist the bare wires tightly, as	12 to 15 mm
	speaker cables, and twist the bare wires tightly, as
	shown.

■Push-type speaker terminals

Strip 10 to 12 mm of insulation from the ends of the speaker cables,	10 to 12 mm
and twist the bare wires tightly, as shown.

Image 11

Contents TX-NR579 Away from the rear panel or wall, creating a flue-like Local regulations when disposing of batteries10 cm 4 at the rear. The rear edge of the shelf or Board above the apparatus shall be set 10 cmBatteries and Heat Exposure Warning PrecautionsPower Preventing Hearing Loss CautionAiming the remote controller Supplied AccessoriesMake sure you have the following accessories Installing the batteriesContents Processing FeaturesServices available may vary depending on the region AmplifierFront Panel Front & Rear PanelsFor detailed information, see the pages in parentheses DisplayRear Panel Power cordUREMOTE Control jack See Connecting the AV Receiver for connection pages 11 toControlling the AV Receiver Remote ControllerScrew-type speaker terminals Connecting the AV ReceiverConnecting Your Speakers Connecting the Speaker CablesAttaching the Speaker Cable Labels Speaker ConfigurationSpeaker Connection Precautions Bi-amping the Front Speakers Using a Powered SubwooferHdmi cable Connecting AV componentsAbout AV Connections AV Cables and JacksJack Components Assignable Connecting Components with HdmiAudio Return Channel ARC function Jack/Port Components Assignable Connecting Your ComponentsHow to record a video source Remote Control Connecting Onkyo uComponentsConnecting a Recording Component System On/Auto Power OnAssembling the AM loop antenna Connecting the AntennasConnecting the Power Cord Plug the power cord into an AC wall outletAV receiver comes on, the display lights Turning On/Off the AV ReceiverTurning On Turning OffPlaying the Connected Component Controlling Contents of USB or Network DevicesSelecting the Language for the Onscreen Setup Menus PlaybackEnter Understanding Icons on the DisplayPlaying an iPod/iPhone via USB Listening to Internet Radio Playing a USB DeviceTop menu of Internet Radio Listening to Other Internet RadioRegistering My Favorites*1 Remote Playback Windows Media Player 11 SetupWindows Media Player 12 Setup Playing Music Files on a ServerListening to AM/FM Radio Using Remote PlaybackUsing the Tuner Tuning into Radio StationsMode Presetting AM/FM StationsUsing RDS Listening to Traffic News TP Displaying Radio Text RTFinding Stations by Type PTY Measurement procedure Using Basic FunctionsUsing the Automatic Speaker Setup Use q/wto select a target, and use e/rto change the setting When you’ve finished making the settings, pressWhen prompted, repeat step ` CancelChanging the Speaker Setup Manually Error MessagesSelecting Listening Modes Using the Listening ModesInput Source Following audio formats are supported by the listening modeAbout Listening Modes Explanatory NotesListening Modes Onkyo-Original DSP Listening ModesHeight Resolution AudioDolby Pro Logic Dolby Pro Logic IIzThat fully envelops the listener Listening Mode Description Input Speaker Source Layout Neo6Use this mode with any stereo movie e.g., TV, DVD, VHS Setting the Display Brightness Using the Home MenuUsing the Sleep Timer VCR/DVR Displaying Source InformationChanging the Input Display Muting the AV ReceiverAV Recording Using HeadphonesRecording Explanatory Notes Advanced SetupOn-screen Setup Menus Common Procedures in Setup Menu Hdmi Input ResolutionInput/Output Assign Monitor OutDigital Audio Input Speaker SetupInput selector Default assignment Component Video InputSpeaker Settings Unit Speaker DistanceLevel Calibration Double BassDolby Audio AdjustMultiplex/Mono Audyssey Source SetupTheater-Dimensional Reference Level Dynamic VolumeName Edit IntelliVolumeSync Picture Adjust Audio Selector Charge ModeDTS/DTS-ES/DTS-HD Listening Mode PresetVolume Setup MiscellaneousTuner Hardware SetupOSD Setup Remote IDAuto Standby Dhcp Firmware UpdateNetwork Using the Audio Settings Remote Controller SetupLock Setup CinemaFILTER Late NightMusic Optimizer Making Zone 2 Connections Connecting Your Zone 2 Speakers Directly to the AV receiverConnecting the Zone Speakers to an Additional Amplifier ZoneMuting Zone Adjusting the Volume for ZoneOperating on the remote controller Controlling Zone 2 ComponentsUP-A1 Dock Using the Onkyo DockIPod/iPhone Playback via Onkyo Dock RI Dock Controlling Your iPod/iPhoneAvailable buttons Controlling Other Components Preprogrammed Remote Control CodesLooking up for Remote Control Code Entering Remote Control CodesControlling Other Components Remote Control Codes for Onkyo Components Connected via uResetting Remote Mode Buttons Resetting the Remote ControllerSearch SetupButtons Input TV VOL q / w GuideAudio TroubleshootingPower About DTS signals There’s no sound with a certain signal formatCan’t select the Pure Audio listening mode Speaker volume cannot be set as requiredTuner Remote ControllerVideo Music Server and Internet Radio UP-A1 Dock for iPod/iPhoneRecording ZoneOthers USB Device PlaybackComponent Video OUT Important Note Regarding Video PlaybackNetwork Requirements Network/USB FeaturesConnecting to the Network Remote playback Server RequirementsUSB Device Requirements Server playbackAbout Dlna Supported Audio File FormatsBefore you start Firmware UpdateUpdate procedure Updating the Firmware via NetworkUpdating the Firmware via USB TroubleshootingErrors during an update via network Error Code DescriptionErrors during an update via USB Video Connection Formats Connection Tips and Video Signal PathSignal Selection OUT Audio Connection FormatsAbout Copyright Protection About HdmiSupported Audio Formats Operations that can be performed with Connection Using an RIHD-compatible TV, Player, or RecorderAbout p-compatible components Operate with the remote controller How to connect and setupConfirm the connecting and setting Confirm the settingsVideo Section SpecificationsAmplifier Section General1080p 1080i 720p 480p/576p 480i/576i Component Composite Video Resolution ChartAvailable resolutions 3840 ⋅ 2160 24/25/30 Hz OutputOnkyo Europe Electronics GmbH UK Branch Onkyo Europe Electronics GmbH

TX-NR579 specifications

The Onkyo TX-NR579 is a versatile and powerful AV receiver that caters to both home theater enthusiasts and casual listeners alike. This model distills advanced audio technologies while maintaining user-friendly features that enhance the overall entertainment experience.

One of the standout features of the TX-NR579 is its support for 7.2-channel output, allowing users to connect various speakers to create a rich, immersive surround sound setup. With a robust power output of 100 watts per channel, this receiver can drive a range of speakers with ease, ensuring clear and dynamic sound reproduction across a variety of media types.

The TX-NR579 incorporates advanced audio technologies such as Dolby TrueHD and DTS-HD Master Audio, ensuring that users experience studio-grade sound quality for their movies and music. In addition, the receiver supports a variety of audio formats, allowing for seamless playback of different media sources.

Another notable feature is the inclusion of 4K Ultra HD video pass-through with HDR support. This enables users to enjoy stunning picture quality and vibrant colors when paired with compatible devices. With multiple HDMI inputs, the TX-NR579 accommodates various sources such as Blu-ray players, gaming consoles, and streaming devices, making it a central hub for home entertainment.

The receiver is equipped with Onkyo's AccuEQ room acoustics calibration system, which analyzes the sound environment and optimizes audio playback for the specific room. This ensures that users get the best possible sound experience tailored to their listening space.

For connectivity, the TX-NR579 offers built-in Wi-Fi and Bluetooth capabilities, allowing for easy streaming from smartphones, tablets, and other devices. Users can take advantage of popular services like Spotify and Pandora directly through the receiver, adding a convenient way to access music.

With its intuitive user interface and remote control compatibility, the TX-NR579 is designed for easy navigation and operation. Whether setting up a movie night or enjoying a music session, this receiver stands as a versatile solution for elevating home entertainment.

In summary, the Onkyo TX-NR579 combines powerful audio performance with advanced features, making it an ideal choice for both serious audiophiles and those looking to enhance their home cinema experience. Its exceptional sound quality, 4K support, and user-friendly design position it as a reliable addition to any home theater setup.