LG Electronics HS102 owner manual Safety Instructions

Page 4

Safety Instructions

Safety Instructions

Please take note of the safety instructions to prevent any potential accident or misuse of the projector.

Safety Instructions are given in two forms as detailed below.

WARNING : The violation of this instruction may cause serious injuries and even death.

NOTES : The violation of this instruction may cause light injuries or damage to the projector.

After reading this manual, keep it in the place that the user always can contact easily.

Indoor Installation

Do not place the Projector in direct sunlight or near heat sources such as radiators, fires and stove etc.

This may cause a fire hazard !

WARNING

Do not place inflammable materi-

Do not allow children to hang on

als beside the projector

the installed projector.

This may cause a fire hazard !

It may cause the projector to fall, caus-

ing injury or death.

 

 

Indoor Installation

NOTES

 

 

 

Disconnect from the mains and remove all connections before moving.

Do not place the projector close to sources of steam or oil such

as a humidifier.

This may create a fire hazard or an electric shock hazard !

Do not place the projector where it might be exposed to dust.

This may cause a fire hazard or damage to the unit!

When installing the projector on a table, be careful not to place it near the edge.

This may cause the projector to fall causing serious injury to a child or adult and serious damage to the projector.

Only use a suitable stand.

Only use the projector on a level and stable surface.

It may fall and cause injury and/or damage to the unit.

Ensure good ventilation around the projector. The distance between the projector and the wall should be more than 30cm/12 inches.

An excessive increase in its internal temperature may cause a fire hazard or damage to the unit!

Do not block the vents of the pro- jector or restrict air-flow in any way.

This would cause the internal tempera- ture to increase and could cause a fire hazard or damage to the unit!

Do not place the projector directly on a carpet, rug or place where ventilation is restricted.

This would cause its internal temperature to increase and might create a fire hazard or damage the unit.

 

Outdoor Installation

WARNING

 

 

 

Do not use the projector in a damp place such as a bathroom where it is likely to get wet.

This may cause a fire or an electric shock hazard !

 

Power

WARNING

 

 

 

Earth wire should be connected.

If the earth wire is not connected, there is a possible danger of electric shock caused by the current leakage.

If grounding methods are not possible, a separate circuit breaker should be installed by a qualified electrician.

Do not connect ground to telephone wires, lightning rods or gas pipe.

The mains plug should be inserted fully into the power outlet to avoid a fire hazard !

This may cause a fire hazard or damage the unit.

Do not place heavy objects on the power cord.

This may cause a fire or an electric shock hazard !

4

Image 4
Contents HS102 HS102G DLP Projector Contents Safety Instructions Do not use too many plugs on the Mains multi-outlet Be damagedDo not allow any objects to fall into the projector Dispose of used batteries care- fully and safelyDo not use water while cleaning the projector Batteries BatteryDo not drop the projector or allow impact shock Do not place heavy objects on Top of projectorConnecting Part Names of partsMain Body Names of partsControl Panel Remote Control Installing BatteriesAccessories Optional ExtrasInstalling and Composition Installation InstructionsInstalling and Composition This may cause overheating of the projectorHow to install the projector using the tripod Basic Operation of the Projector Projection distance based on the picture formatUsing Kensington Security System Turning on the Projector Turning off the ProjectorSelecting source mode Press the Source button on the top cover or remote controlFocus and Position of the Screen Image Each press of the , button changes the display as belowConnecting to a Desktop PC Connecting to a Notebook PCConnecting to a Video Source ConnectionConnecting to a DVD Connecting to a D-TV Set-Top BoxAdjusting Video FunctionVideo Menu Options FunctionPicture mode Color Temperature ControlSmart picture Function Black level FunctionKeypad Sound Function Keypad LED FunctionScreen Capture Function Press the OK button again to save Screen capture imageUsing Ratio Function Special Menu OptionsSelecting Language Overscan FunctionFlip vertical Function Flip horizontal FunctionThis function reverses the projected image vertically Sleep time Function Sleep timer turns the projector off at the preset timeAuto sleep Function Using Keystone Function Presentation timer FunctionKeystone can be adjusted from -20 to Using Blank Function Press the Blank button on the remote controlPress any button to cancel the blank function Selecting Blank imageLED mode Function Auto configure Function Using Phase FunctionUsing Clock Function Press the Auto button of the remote controllerUsing Horizontal Function Using Vertical FunctionTo use the USB device Connecting the USB deviceImage shown may differ from your projector Set up the menu in Full-Sized screen Photo ListScreen Components Press USB button to return to the DivX Home menuViewing the Slide show UsePress Button to select Button to select the desired photosMusic List It is impossible to delete only one music in music listUSB Movie List Movie ListDivX Audio Language & Subtitle Language DivX registration codePress OKbutton DivX Registration CodeSupported Monitor Display DVD/DTV Input SignalInformation Cleaning the lens MaintenanceCleaning the Projector Case Specifications Operating Condition TemperatureHS102 HS102-JE / HS102G HS102G-JE Humidity