LG Electronics HS102 owner manual Installing and Composition, Installation Instructions

Page 11

Installing and Composition

Installing and Composition

Installation Instructions

* Don’t place the projector in the following conditions. It may cause malfunction or product damage.

Provide proper ventilation for this projector.

●The projector is equipped with ventilation holes(intake) on the bottom and ventilation holes(exhaust) on the front. Do not block or place anything near these holes, or inter- nal heat build-up may occur, causing picture degradation or damage to the projector.

●Do not place the projector on a carpet, rug or other similar surface. It may prevent a adequate ventilation of the projector bottom. This product should be mounted to a wall or ceiling only.

●Never push projector or spill any kind of liquid into the projector.

●Leave an adequate distance(30cm/12 inches or more) around the projector.

Place this projector in adequate temperature and humidity conditions.

●Install this projector only in a location where adequate temperature and humidity is available. (refer p.41)

Don’t place the projector where it can be covered with dust.

●This may cause overheating of the projector.

Do not obstruct the slots and openings of the projector. This may cause overheating and create a fire hazard.

The projector is manufactured using high-precision technology. You may, however, see tiny black points and/or bright points (red, blue, or green) that continuously appear on the projector Screen. This is a nor- mal result of the manufacturing process and does not indicate a malfunction.

To display DTV programs, it is necessary to purchase a DTV receiver (Set-top Box) and connect it to the projector.

When the remote control does not work during operation.

●The remote control may not work when a lamp equipped with electronic ballast or a three-wavelength lamp is installed. Replace those lamps with international standard products to use the remote control normally.

11

Image 11

Contents HS102 HS102G DLP Projector Contents Safety Instructions Dispose of used batteries care- fully and safely Do not use too many plugs on the Mains multi-outletBe damaged Do not allow any objects to fall into the projectorDo not place heavy objects on Top of projector Do not use water while cleaning the projectorBatteries Battery Do not drop the projector or allow impact shockNames of parts Connecting PartNames of parts Main BodyControl Panel Installing Batteries Remote ControlOptional Extras AccessoriesThis may cause overheating of the projector Installing and CompositionInstallation Instructions Installing and CompositionHow to install the projector using the tripod Projection distance based on the picture format Basic Operation of the ProjectorUsing Kensington Security System Turning off the Projector Turning on the ProjectorEach press of the , button changes the display as below Selecting source modePress the Source button on the top cover or remote control Focus and Position of the Screen ImageConnection Connecting to a Desktop PCConnecting to a Notebook PC Connecting to a Video SourceConnecting to a D-TV Set-Top Box Connecting to a DVDFunction Adjusting VideoFunction Video Menu OptionsColor Temperature Control Picture modeBlack level Function Smart picture FunctionKeypad LED Function Keypad Sound FunctionPress the OK button again to save Screen capture image Screen Capture FunctionOverscan Function Using Ratio FunctionSpecial Menu Options Selecting LanguageThis function reverses the projected image vertically Flip horizontal FunctionFlip vertical Function Auto sleep Function Sleep timer turns the projector off at the preset timeSleep time Function Keystone can be adjusted from -20 to Presentation timer FunctionUsing Keystone Function Selecting Blank image Using Blank FunctionPress the Blank button on the remote control Press any button to cancel the blank functionLED mode Function Press the Auto button of the remote controller Auto configure FunctionUsing Phase Function Using Clock FunctionUsing Vertical Function Using Horizontal FunctionImage shown may differ from your projector Connecting the USB deviceTo use the USB device Press USB button to return to the DivX Home menu Set up the menu in Full-Sized screenPhoto List Screen ComponentsButton to select the desired photos Viewing the Slide showUse Press Button to selectIt is impossible to delete only one music in music list Music ListUSB Movie List Movie ListDivX Registration Code DivX Audio Language & Subtitle LanguageDivX registration code Press OKbuttonInformation DVD/DTV Input SignalSupported Monitor Display Cleaning the Projector Case MaintenanceCleaning the lens Humidity SpecificationsOperating Condition Temperature HS102 HS102-JE / HS102G HS102G-JE