APPENDIX
01.Power (Command: k a)
To control Power On/Off of the TV.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off | Data 01 : Power On |
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
To show Power On/Off.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
*If there is the time delay between command and ack message during power on sequence, It should be described like “Note: In this model, set will send the Acknowledge after power on processing com- pletion. There might be a time delay between com- mand and acknowledge.”
02.Aspect Ratio (Command: k c) (Main picture size) To adjust the screen format. (Main picture format)
You can adjust the screen format using the Aspect Ratio in the Picture menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01: Normal screen (4:3) | Data 06: Original |
Data 02: Wide screen (16:9) | Data 07: 14:9 |
Data 04: Zoom1 | Data 09: Just Scan |
Data 05: Zoom2 |
|
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
*Using the
* Just Scan works in the following mode: Component (720p/1080i/1080p), HDMI (720p/1080i/1080p)
03.Screen Mute (Command: k d) To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 : Screen mute off (Picture on)
Data 01 : Screen mute on (Picture off)
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
04. Volume Mute (Command: k e)
To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
Data 01 : Volume mute off (Volume on)
Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
05.Volume Control (Command: k f) To adjust volume.
You can also adjust volume with the volume buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64
Refer to ‘Real data mapping 1 ’. See page 68. Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
06.Contrast (Command: k g) To adjust screen contrast.
You can also adjust contrast in the Picture menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64
Refer to ‘Real data mapping 1 ’. See page 68.
Acknowledgement [g][ ][Set ID][ ][OK][Data][x]
07.Brightness (Command: k h) To adjust screen brightness.
You can also adjust brightness in the Picture menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64
Refer to ‘Real data mapping 1 ’. See page 68.
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
08. Colour (Command: k i)
To adjust the screen colour.
You can also adjust colour in the Picture menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64
Refer to ‘Real data mapping 1 ’. See page 68.
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
09. Tint (Command: k j)
To adjust the screen tint.
You can also adjust tint in the Picture menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64
Refer to ‘Real data mapping 1 ’. See page 68.
Acknowledgement [j][ ][Set ID][ ][OK/NG][Data][x]
66