LG Electronics MT-50PZ40/, MT-50PZ41/, MT-50PZ43/, MZ-50PZ42/, MZ-50PZ43 How to connect

Page 8

Watching VCR (When the Interface board is installed.)

The interface board(AP-50EA40/41) is not equipped on MT/MZ-50PZ42/43 series models.

When connecting the Plasma Monitor with external equipments, match the colors of connecting ports (Video - yellow, Audio(L) - white, Audio(R) -red).

Connect the VIDEO INPUT socket(yellow) with the BNC-RCA adapter to the VIDEO INPUT socket of the set.

If you have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the Plasma Monitor. If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regu- lar VCR to the Video input.

Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.

Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR, 4:3 picture format or if a CH label is present; the fixed image may remain visible on the screen.

Use the orbiter function to avoid having a fixed image. (Refer to p.18)

1.Press INPUT SELECT button on the remote control and select Video or (AV1 or AV2). (When connecting with S-Video, select the S-Video)

2.Insert a video tape into the VCR and press the PLAY button on the VCR. (See VCR owner’s manual)

Watching Cable TV (When the Interface board is installed.)

The interface board(AP-50EA40/41) is not equipped on MT/MZ-50PZ42/43 series models.

After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV program- ming. This monitor cannot display TV programming without a TV tuner device or cable TV converter box connected to the monitor.

1.Press INPUT SELECT button on the remote control and select Video or (AV1 or AV2).

2.Tune to cable service provided channels using the cable box.

Watching external AV source (When the Interface board is installed.)

The interface board(AP-50EA40/41) is not equipped on MT/MZ-50PZ42/43 series models.

When connecting the Plasma Monitor with external equipments, match the colors of connecting ports. Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.

1.Press INPUT SELECT button on the remote control of the monitor to select Video or (AV1 or AV2).

2.Operate the corresponding external equipment. (See external equipment operating guide.)

Watching DVD (When the Interface board is installed.)

The interface board(AP-50EA40/41) is not equipped on MT/MZ- 50PZ42/43 series models.

How to connect

Connect DVD video inputs to Y, PB, PR of COMPONENT (DVD

INPUT) and audio inputs to Audio sockets of AUDIO INPUT.

Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.

How to use

1.Press INPUT SELECT button on the remote control of the monitor to select Component or (AV1 or AV2).

2.Try this after turning on the DVD player.

(Refer to the DVD player's manual for operating instructions.)

•Component Input ports

You can get better picture quality if you con- nect DVD player with component input ports as below.

Component ports of the

Y

PB

PR

Monitor

 

 

 

 

 

 

 

Video output ports

Y

Pb

Pr

Y

B-Y

R-Y

of DVD player

Y

Cb

Cr

 

Y

PB

PR

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents
Plasma Monitor LG Plasma Monitor Contents Safety Instructions Earth wire should be connected Do not use water the Monitor while cleaning Do not insert any object into the exhaust ventOnly use the specified batteries Do not pull the cord but the plug when unpluggingObjects like a heater Back Panel Controls of the MonitorFront Panel Controls Watching External Equipments Back Panel RCA TypeScart Type External Speaker 8 ohm outputWatching VCR When the Interface board is installed Watching Cable TV When the Interface board is installedWatching DVD When the Interface board is installed How to connectPC Setup Connecting PCSetup Instructions to Connect a PC to your Monitor Displayable Monitor Specification RGB1 mode Resolution Horizontal VerticalResolution Horizontal Vertical RGB2 mode Resolution Horizontal VerticalControls of the remote control Installing BatteriesAccessories Optional ExtrasTo install as desktop type Monitor InstallationTo install as wall mounting type Menu language setup Turning on the Monitor just after installationTurning on the Monitor power cord is still connected Adjusting volume levelAdjusting Auto Color Control Manual Color Temperature ControlUser optionVideo Menu PSM Picture Status MemoryAVL Auto Volume Leveler Adjusting Sound Manual SettingPress the SSM button to select the picture appearance setup Audio MenuSetting the Clock Setting the On/Off TimerSleep Timer Time MenuSpecial Menu Child lockOrbiter White WashAuto adjustment RGB1PC mode only Setting Picture FormatScreen Menu Split ZoomScreen Position Manual Configure RGB1PC mode onlyInitializing Reset to factory value PIP Function Sub Picture Size Adjustment Twin PictureSelecting a source for the Twin picture Swapping the Twin PictureExternal Control Device Setup Type of connector D-Sub 9-pin maleRS-232C configurations Set IDCommand Reference List Power CommandaInput select Commandb Main picture input Transmission / Receiving ProtocolAspect Ratio Commandc Main picture format Screen mute CommanddVolume mute Commande Volume control CommandfSharpness Commandk PIP Size CommandoOSD select Commandl Remote control lock mode CommandmBalance Commandt Color temperature CommanduRed Adjustment Commandv Green Adjustment CommandwOrbiter Time Setting Commandr Orbiter Pixel Setting CommandsReal data mapping 1 0 Step Real data mappingEnglish Troubleshooting check list No pictureNo sound No output from oneProduct specifications English Model
Top Page Image Contents