Mitsubishi Electronics XD1000 Viewing computer images, Connecting the projector to a computer

Page 13

Viewing computer images

A. Connecting the projector to a computer

Preparation:

Make sure that the power of the projector and that of the computer are turned off.

When connecting the projector to a desktop computer, disconnect the RGB cable that is connected to the monitor.

ENGLISH

COMPUTER IN/COMPONENT VIDEO IN-1

For analog connection:

(For using the COMPUTER/COMPONENT VIDEO IN-1 terminal.)

1

2

COMPUTER IN/COMPONENT

VIDEO IN-2

424 ); $2$ **8 8

1

2

to monitor port

RGB cable

to monitor port (5 BNC)

1.Connect one end of the supplied RGB cable to the COMPUTER IN/COMPONENT VIDEO IN-1 terminal of the projector.

2.Connect the other end of the RGB cable to the monitor port of the computer.

When viewing images supplied from an analog-connected computer, press the COMPUTER button on the remote control.

For analog connection:

(For using the COMPUTER/COMPONENT VIDEO IN-2 terminal.)

1.Connect one end of a commercially BNC cable to the COMPUTER IN/COMPONENT VIDEO IN-2 terminal of the projector.

2.Connect the other end of the BNC cable to the 5 BNC terminals of the monitor port of the computer.

8 **8 $2$ ); 424

DVI-D (HDCP)

For digital connection:

1.Connect one end of a commercially available DVI cable to the DVI-D (HDCP) terminal of the projector.

2.Connect the other end of the DVI cable to the DVI terminal of the computer.

1

2

to DVI

 

DVI cable

When viewing images supplied from a digital-connected computer, press the DVI-D(HDCP) button on the remote control.

Turn on the main power switch of the projector before starting the computer.

For audio connection:

1.Connect one end of a commercially available PC audio cable to the AUDIO IN-1/2 terminal of the projector.

Computer

2. Connect the other end of the PC audio cable to the audio

1

AUDIO IN

PC audio cable (option)

AUDIO OUT

to audio output

output terminal of the computer.

This projector uses stereo pin jack for its audio input. Check the type of the audio output terminal of the connected computer and prepare a proper cable for connection. Some computers don't have the audio output terminal.

Speaker output is mono.

2 terminal

Additional devices, such as a conversion connector and an analog RGB output adapter, are required depending on the type of the computer to be connected.

Use of a long cable may decrease the quality of projected images.

Images may not be projected correctly, depending on the type of the connected computer.

When DVI-D signal is input, some signal setting menus are unavailable.

Also read the instruction manual of the equipment to be connected.

Contact your dealer for details of connection.

EN-13

Image 13
Contents XD1000 Compliance Notice When using the projector in EuropeContents Important safeguards Do not look into the lens when it is operating Do not keep using the damaged projectorPlace of installation Never remove the cabinet Do not modify this equipmentInserting the batteries into the remote control Checking accessoriesPreparing your projector Control panel OverviewTerminal board How to disable the Laser button Lamp cover Adjustment feetHow to enable the Laser button Preparating your projectorOperational range of the remote control Using the remote controlUsing the wired remote control Reception angleSetting up the screen Setting up your projectorBasic setup Adjusting the projection angleRear projection Front projection, ceiling mountingWhen the aspect ratio of the screen is Setting up your projectorScreen size and projection distance Lens Shift buttonViewing computer images Connecting the projector to a computerViewing computer images Plugging the power cordTerminal cover Remove the lens cap Projecting imagesExample of the setting procedure for external output When connecting to a notebook computerTo stop projecting Instant Shut DownConnecting to a video player, etc Connecting the projector to video equipmentViewing video images Connecting to video equipment having a DVI-D terminal Plugging in the power cordViewing video images Projector + DVD player or Hdtv decoderProjecting images AV mute Volume from the speakerHow to change the settings Setting the aspect ratioWith the remote control With the Feature menuMenu operation How to set the menusInstallation menu Available settings in the menusImage menu Signal menu Feature menuMenu operation To adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To cancel the menuTo adjust the tone of white Color Temp Adjusting projected imagesAbout color temperature Color EnhancerLPF To adjust the vertical positionPassword function Advanced featuresTo enable the password function To cancel the password functionPicture in Picture PinP ExpandStill Mouse remote control Advanced featuresProjector + computer with USB connector PageUp buttonProjectorView Supervising and controlling by computerPJLink About PJLinkReplacing the lamp Interval of lamp replacementCleaning of the lens Cleaning of the projector and the ventilation slotsReset of the lamp operation time To replace the lampNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution Others Problem Solution TroubleshootingNormal condition IndicatorsAbnormal condition Specifications Replacement part Option / Not included in the boxEN-39 Dimension Drawings unit mm ConnectorsSpecifications Mitsubishi Projector Contact Information