Mitsubishi Electronics XD2000 Viewing computer images, Plugging the power cord, Terminal cover

Page 14

Viewing computer images (continued)

Monitor

1 MONITOR OUT

RGB cable

1

AUDIO OUT

to audio input

2

Audio cable (option)

 

About DDC

For monitor connection:

1.Connect one end of the RGB cable that is connected to the MONITOR OUT terminal of the projector.

For audio output connection:

1.Connect one end of a commercially available audio cable to the audio output terminal of the projector.

2.Connect the other end (white and red) of the audio cable to the audio output terminals (L, R) of the audio equipment.

When the audio cable is connected to the AUDIO OUT ter- minal, the speaker output is muted.

The COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC1/2B standard and the COMPUTER/COMPONENT VIDEO DVI-D (HDCP) terminal complies with the DDC2B standard. When a computer supporting this standard is connected to this terminal, the computer will automatically load the information from this projector and prepare for output of appropriate images.

When connecting a DDC-supporting computer to the projector, turn on the main power switch of the projector before starting the computer.

B. Plugging the power cord

Earthing terminal

1.Plug the attached power cord into the power cord inlet of this projector.

2.Plug the other end of the power cord into a power outlet.

1

2

 

Power cord (Example)

The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.

This projector uses the power plug of 3-pin grounding type. Do not take away the grounding pin from the power plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.

The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or power supply using other voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare an appropriate power cord separately.

Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.

Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause fire or electric shock.

Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fire or electric shock.

Caution:

Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord.

Do not plug in or out the power cord with your hand wet. It may cause electric shock.

Terminal cover

This projector includes a terminal cover. If necessary, install the terminal cover to the projector.

Install the terminal cover

1. Fit two hooks of the terminal cover into the projector.

2. Tighten the attachment screws (a) firmly.

• Don’t carry the projector by the terminal cover.

(a)

EN-14

Image 14
Contents XD1000 When using the projector in Europe Compliance NoticeContents Important safeguards Place of installation Do not keep using the damaged projectorDo not look into the lens when it is operating Never remove the cabinet Do not modify this equipmentPreparing your projector Checking accessoriesInserting the batteries into the remote control Terminal board OverviewControl panel How to enable the Laser button Lamp cover Adjustment feetHow to disable the Laser button Preparating your projectorUsing the wired remote control Using the remote controlOperational range of the remote control Reception angleBasic setup Setting up your projectorSetting up the screen Adjusting the projection angleFront projection, ceiling mounting Rear projectionScreen size and projection distance Setting up your projectorWhen the aspect ratio of the screen is Lens Shift buttonConnecting the projector to a computer Viewing computer imagesTerminal cover Plugging the power cordViewing computer images Projecting images Remove the lens capTo stop projecting When connecting to a notebook computerExample of the setting procedure for external output Instant Shut DownViewing video images Connecting the projector to video equipmentConnecting to a video player, etc Viewing video images Plugging in the power cordConnecting to video equipment having a DVI-D terminal Projector + DVD player or Hdtv decoderProjecting images Volume from the speaker AV muteWith the remote control Setting the aspect ratioHow to change the settings With the Feature menuHow to set the menus Menu operationImage menu Available settings in the menusInstallation menu Menu operation Feature menuSignal menu To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To cancel the menuAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerTo adjust the vertical position LPFTo enable the password function Advanced featuresPassword function To cancel the password functionStill ExpandPicture in Picture PinP Projector + computer with USB connector Advanced featuresMouse remote control PageUp buttonPJLink Supervising and controlling by computerProjectorView About PJLinkInterval of lamp replacement Replacing the lampReset of the lamp operation time Cleaning of the projector and the ventilation slotsCleaning of the lens To replace the lampTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Troubleshooting Others Problem SolutionAbnormal condition IndicatorsNormal condition Replacement part Option / Not included in the box SpecificationsEN-39 Specifications ConnectorsDimension Drawings unit mm Mitsubishi Projector Contact Information