I n g t h e u n i t | Mitsubishi Electronics LVP-X30U instruction

Mitsubishi Electronics LVP-X30U user manual I n g t h e u n i t, Connect the power cord

Page 16

E – 14

O p e r a t i o n

U s i n g t h e u n i t

Before Using

Open the sliding lens cap.

1 Connect the power cord.

The POWER indicator will light amber, the ex- haust fan will operate at slow speed and the standby status will be activated.

Lights in amber (Standby)

POWER STATU

POWER SO

				VIDEO
				EO
MO				S VID
MO	RGB	/ YCbC	r	1
		/ YCbC
USE
USE
AUDIO
Power cable				2
(supplied)				2
(supplied)

2 Press POWER on the remote control, or POWER on top of the unit, to turn on the unit.

The POWER indicator on top of the unit turns to green and starts flashing.

It takes one minute for the unit to be ready for use. Wait until the indicator stops flashing and lights steadily in green.

MOUSE POWER

VIDEORGB

CANCEL

Green light flashes (About one minute)

↓

		Then lights steadily
POWER	ST	in green
	POWER

Note

While the POWER indicator is flashing, the unit doesn’t turn off even if you press POWER on the remote control, or POWER on the unit.

3 Turn on the connected source (computer, VCR, DVD player, etc.).

If you use a video component, start playback for screen/image adjustment.

4 Select the input by pressing either the VIDEO or RGB button of the remote con- trol, or the SOURCE button of this device (refer to page 16).

MOUSE POWER

VIDEO

RGB

SOURCE

CANCEL

Notes

•If the blue or black screen (the background type differs depending on the “BACKGROUND” setting. See page 28.) is projected, check the following:

–Is the source properly connected to the unit?

–Is the source component or computer turned on?

–Are the video signals coming to the unit?

•The video resolution of the connected computer can be changed. See page 13.

5 Adjust the position and height of the unit.

Move the unit to the position where the projected image is horizontally centered to the screen.

•When the projected image is offset horizontally

Adjust the position of the unit so that the unit is

square to the screen.
View from the top	Screen

•When the projected image is offset ver- tically

Adjust the height balance of the unit with the adjusters. See next page.

Side view

Screen

(Continued on next page.)

Image 16

Contents

Data Projector Page English Precautions Important SafeguardsInstallation Power SupplyCleaning Lamp ReplacementFire and Shock Precautions B l e o f c o n t e n t sA t u r e s Other main features you’ll enjoyE c k i n g t h e P p l i e d a c c e s s o r i e s Remote control effective range E p a r i n g t h e M o t e c o n t r o lInserting the batteries Press firmly and slidePower indicator 14,16 Status indicator Power button 14,16 Auto button Source button 14 Speaker 10R t s a n d c o n t r o l s Top, front and side panel view Control panelTerminal Panel Rear and side panel viewBuilt-in Security Slot Enter button 17 Infrared transmitter LEDInstallation Positioning the unit N n e c t i n g v i d e o e q u i p m e n t Connection to the Video jack of the unit Rear panel jacks of this device Connection to the S-VIDEO jack of the unitConnection to the RGB/YCbCr connector N n e c t i n g a P C o r M a c i n t o s h Changing the computer’s video resolutions Windows 98/WindowsWindows MacintoshConnect the power cord Adjust the position and height of the unitI n g t h e u n i t Turn on the connected source computer, VCR, DVD player, etcCase of RGB input, adjust the video of the connected PC After using the unit I n g t h e u n i t N t i n u e dUSB Port Connection Remote control mouse functionsIBM PS/2 Mouse Port Connection Automatic Screen Adjustment Adjusting the VolumeKeystone Adjustment Freezing animated imagesEnlarging the picture To move to the desired portion of the enlarged pictureScreen Reduction N u S t r u c t u r e Normal menu RGB input Advanced menu J u s t i n g t h e p i c t u r e e l e m e n t s To close the menuTiming Chart Adjusting Clock Frequency and Phase Adjusting the position of the imageIf no images appear during setting N u a l a d j u s t m e n t C o m p u t e r I m a g e sResetting Resetting the time the hours of lampS e t t i n g S e t t i n g t h e L a m p H o u r s o f U s a g eSetting the Video Type Adjusting Color BalanceT t i n g N a r r o w I m a g e s a d v a n c e d M e n u Selecting the Color SystemSetting the RGB/YCbCr connector Setting the Display FrameSetting Filter Select the input for image selectionSetting the partial display position I t i a l S e t t i n g sAudio Muting Selecting the BackgroundAuto Source Settings Using the Power Saving FunctionUse the cursor $ / % keys to set Power Saving to on or OFF Selecting a Projection TypeT t i n g t h e M e n u Troubleshooting Status Light Messages Lamp cartridge replacement procedure P l a c i n g t h e l a m pR t r i d g e StepSpecification s Sub Pin AssignmentsDimensions 48 mm177 mm/7.0 ″ 230mm/9.0 ″

Mitsubishi Electronics LVP-X30U user manual I n g t h e u n i t, Connect the power cord