Mitsubishi Electronics LVP-X30U user manual P l a c i n g t h e l a m p, R t r i d g e, Step

Page 35

R e p l a c i n g t h e l a m p

The rated lamp life is about 1,000 hours. The rated lamp life is the average life of the lamps produced and tested (under the test conditions of our company) for a long term, however, it may become shorter depending on the conditions of usage.

After the lamp has been operating for 1000 hours or longer, the STATUS indicator on the control panel will light and the “LAMP USAGE” icon which shows hours of total lamp usage will be displayed on the screen. When this happens, turn off the unit and replace the lamp cartridge with a new one. The unit will not turn on after 1100 hours. (It will go off if it is in use.)

CAUTION

•DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Allow at least one hour for the lamp to cool before handling.

•DO NOT LOOSEN ANY SCREWS except for those men- tioned in the instructions below. There is danger of electric shock.

Lamp cartridge replacement procedure

1Disconnect the power cable.

Wait at least one hour for the lamp to cool.

2Turn the unit upside down carefully.

3Loosen the lamp cover securing screw.

4Remove the lamp cover.

CAUTION: Do not use a lamp cartridge other than the Mitsubishi replacement lamp cartridge. Order this from your dealer using the unit model number (see “Notes” below).

5Loosen the three lamp cartridge securing screws. (This unit has a safety switch.)

6Hold the handle then pull the lamp cartridge upward to remove it.

7Install the new lamp cartridge.

8Secure the lamp cartridge with the three screws.

9Replace the lamp cover and secure it with the securing screw.

10Return the unit to the normal position, connect the power cable, and turn on the unit.

11Reset “LAMP USAGE.” (See page 25).

Notes

•When the lamp usage time reaches 1100 hours, it becomes impossible to switch on the power and menus are not displayed. In such a case, see “If the unit doesn’t go on because lamp usage exceeds 1100 hours” on page 25.

•Obtain a replacement lamp cartridge at the store where the unit was purchased. Please specify the following information when ordering a replacement lamp cartridge:

– Model name : VLT-X30LP

c a r t r i d g e

Step 3

Step 4

Lamp Cover

Step 5

Lamp cartridge

Step 6

Step 7

Step 8

Step 9

ENGLISH

E – 33

Page 34 Page 36
Image 35
Page 34 Page 36
Contents
Data Projector Page English Power Supply PrecautionsImportant Safeguards InstallationB l e o f c o n t e n t s CleaningLamp Replacement Fire and Shock PrecautionsE c k i n g t h e P p l i e d a c c e s s o r i e s Other main features you’ll enjoyA t u r e s Press firmly and slide Remote control effective rangeE p a r i n g t h e M o t e c o n t r o l Inserting the batteriesTop, front and side panel view Control panel Power indicator 14,16 Status indicatorPower button 14,16 Auto button Source button 14 Speaker 10 R t s a n d c o n t r o l sBuilt-in Security Slot Rear and side panel viewTerminal Panel LED Enter button 17 Infrared transmitterPositioning the unit InstallationConnection to the S-VIDEO jack of the unit N n e c t i n g v i d e o e q u i p m e n tConnection to the Video jack of the unit Rear panel jacks of this deviceConnection to the RGB/YCbCr connector N n e c t i n g a P C o r M a c i n t o s h Macintosh Changing the computer’s video resolutionsWindows 98/Windows WindowsTurn on the connected source computer, VCR, DVD player, etc Connect the power cordAdjust the position and height of the unit I n g t h e u n i tCase of RGB input, adjust the video of the connected PC I n g t h e u n i t N t i n u e d After using the unitIBM PS/2 Mouse Port Connection Remote control mouse functionsUSB Port Connection Freezing animated images Automatic Screen AdjustmentAdjusting the Volume Keystone AdjustmentScreen Reduction To move to the desired portion of the enlarged pictureEnlarging the picture N u S t r u c t u r e Normal menu RGB input Advanced menu To close the menu J u s t i n g t h e p i c t u r e e l e m e n t sTiming Chart N u a l a d j u s t m e n t C o m p u t e r I m a g e s Adjusting Clock Frequency and PhaseAdjusting the position of the image If no images appear during settingS e t t i n g t h e L a m p H o u r s o f U s a g e ResettingResetting the time the hours of lamp S e t t i n gSelecting the Color System Setting the Video TypeAdjusting Color Balance T t i n g N a r r o w I m a g e s a d v a n c e d M e n uSelect the input for image selection Setting the RGB/YCbCr connectorSetting the Display Frame Setting FilterSelecting the Background Setting the partial display positionI t i a l S e t t i n g s Audio Muting Selecting a Projection Type Auto Source Settings Using the Power Saving Function Use the cursor $ / % keys to set Power Saving to on or OFFT t i n g t h e M e n u Troubleshooting Status Light Messages Step Lamp cartridge replacement procedureP l a c i n g t h e l a m p R t r i d g eSub Pin Assignments Specification s230mm/9.0 ″ Dimensions48 mm 177 mm/7.0 ″
Top Page Image Contents