Mitsubishi Electronics XL1U user manual User memory for signal setting, Memorizing the setting

VIDEO SIGNAL ...	When AUTO is selected, the appropriate video format is automatically selected depending on the
	input signal. If the image isn’t displayed correctly, select the desired video format manually.
ANAMORPHIC ....	Select ON when playing DVD discs containing data of letterboxed images.
LANGUAGE	Use to select the language used in the menus. (		/ English / Español / Deutsch / Français /
	Italiano /	)
RESET ALL	Use to reset the MENU settings (except LANGUAGE).

ENGLISH

4 SIGNAL
MEMORY CALL	Use to select AUTO, USER 1 or USER 2. See below.
HORIZ. POSITION ....	Use to adjust the horizontal position of the image.
VERT. POSITION	Use to adjust the vertical position of the image.

opt.

SIGNAL

XGA60

FINE SYNC	Use to synchronize the projector with PC input signals so
	that the image is not blurred.
TRACKING	Use to avoid image noise such as wide stripes.
COMPUTER INPUT ....	The unit adjusts itself automatically when connected to a
	DVD player with a component video output (Y, CB, CR). In
	the case ( Y, PB, PR). In the case the projector is connected to
	equipment that includes RGB output terminal, adjust to
	RGB mode.
HOLD	Adjusts the image when flagging occurs near the top of the
	screen.

A	MEMORY CALL	AUTO
U
	HORIZ. POSITION	0
	VERT. POSITION	0
	FINE SYNC.	0
	TRACKING	0
RRGGBB	COMPUTER INPUT	RGB
	HOLD	AUTO

USER MEMORIZE DELETE DEFAULT

5 SIGNAL - USER (Normally, there is no need for adjustments.)
CLAMP POSITION/
CLAMP WIDTH ......... If you use something similar, the brighter colors of the	SIGNAL-USER
projected image may become blurred. In this case, adjust
	CLAMP POSITION	0
CLAMP POSITION or CLAMP WIDTH.
	CLAMP WIDTH	0
HORIZ.PIXELS .. Use to adjust the width of the image. The image size grows
	HORIZ. PIXELS	0
wider as the number increases. (Adjust to the horizontal
	VERT. LINES	0
pixels of the input signal for normal setting.)
	VERT. SYNC.	AUTO
VERT.LINES ...... Use to adjust the height of the image. The image size grows
higher as the number increases. (Adjust to the vertical lines	SHUTTER(U)	0
of the input signal for normal setting.)	SHUTTER(L)	0
VERT.SYNC. ...... Use to adjust the image when its motion does not run	SHUTTER(LS)	0
smoothly. Select AUTO for normal setting.
	SHUTTER(RS)	0
SHUTTER(U) ..... Use to adjust the image when the noise etc. appears on top part

of image.

SHUTTER(L) ...... Use to adjust the image when the noise etc. appears on bottom part of image.

SHUTTER(LS) .... Use to adjust the image when the noise etc. appears on left side of image.

SHUTTER(RS) ... Use to adjust the image when the noise etc. appears on right side of image.

User memory for signal setting

This projector can memorize the maximum of 2 signal menu settings.

Memorizing the setting

1.Select MEMORIZE in the SIGNAL menu, and press the ENTER button.

2.Press the $ or % button to select the memory which you wish to record (USER 1 or USER 2).

3.Press the ENTER button.

•Any buttons are ineffective about 3 seconds of recording setting. Wait for recording to have been completed before operating the buttons.

Initialite the setting which has been changed (Default)

Select RESET in the SIGNAL menu, and press the ENTER button.

Select the user setting

Select MEMORY CALL in SIGNAL menu, and press the $ or % button to select the memory (USER 1 or USER 2).

Reset the recorded setting

1.Select DELETE in the SIGNAL menu, and press the ENTER button.

2.Press the $ or % button to select the memory which you wish to reset (USER 1 or USER 2).

3.Press the ENTER button.

The recorded setting will be reset.

•Any buttons are ineffective about 3 seconds of resetting the recorded setting. Wait for resetting to have been completed before operating the buttons.

EN – 17