Mitsubishi Electronics XL1U user manual Example 1 Set the Auto Power on to on

ITEM	ASCII	HEX				VALUE
SPLASH SCREEN	SS	53h	53h			0	(OFF), 1 (ON)
BACK COLOR	BB	42h	42h			0	(BLACK), 1 (BLUE)
LAMP MODE	LM	4Ch	4Dh			0	(STANDARD), 1 (LOW)
IMAGE REVERSE	IR	49h	52h			0	(OFF), 1 (Mirror), 2 (Invert), 3 (Mirror invert)
MENU POSITION	MP	4Dh	50h			0	(Upper left), 1 (Lower right)
EXPAND MODE	EX	45h	58h			1	- 2
AUDIO MODE	AU	41h	55h			1 (COMPUTER), 2 (VIDEO), 3 (COMPUTER & VIDEO), 4 (MUTE)
VIDEO SIGNAL	VS	56h	53h			0	(AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM) ,
						4	(4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)
ANAMORPHIC	SC	53h	43h			0 (OFF), 1 (ON)
LANGUAGE	LG	4Ch	47h			0	(	), 1 (English), 2 (Español), 3 (Deutsch) ,
						4	(Frençais), 5 (Italiano), 6 ( )
RESET ALL	RSTALL	52h	53h 54h	41h	4Ch 4Ch
MEMORY CALL	MMC	4Dh	4Dh	43h		0	(AUTO), 1 (USER1), 2 (USER2)
HORIZ. POSITION	HP	48h	50h			+ (increase), – (decrease)
VERT. POSITION	VP	56h	50h			+ (increase), – (decrease)
FINE SYNC.	FN	46h	4Eh			00 - 39
TRACKING	TRK	54h	52h	4Bh		+ (increase), – (decrease)
COMPUTER INPUT	CIN	43h	49h	4Eh		0	(RGB), 1 (YCBCR/YPBPR)
HOLD	HLD	48h	4Ch	44h		0	(AUTO), 1 (ON), 2 (OFF)
HOLD BEGIN	HLB	48h	4Ch	42h		–01 - –99
HOLD END	HLE	48h	4Ch	45h		01 - 99
CLAMP POSITION	CLP	43h	4Ch	50h		00 - 63
CLAMP WIDTH	CLW	43h	4Ch	57h		01 - 63
HORIZ. PIXELS	HPL	48h	50h	4Ch		0000 - 9999
VERT LINES	VLN	56h	4Ch	4Eh		0000 - 9999
VERT.SYNC	VSC	56h	53h	43h		0	(AUTO), 1 (ON), 2 (OFF)
SHUTTER (U)	SHU	53h	48h	55h		000 - 383 (000 - 299 for SL1U)
SHUTTER (L)	SHL	53h	48h	4Ch		000 - 383 (000 - 299 for SL1U)
SHUTTER (LS)	SHLS	53h	48h	4Ch	53h	000 - 510 (000 - 398 for SL1U)
SHUTTER (RS)	SHRS	53h	48h	52h	53h	000 - 510 (000 - 398 for SL1U)
MUTE	MUTE	4Dh	55h	54h	45h	0	(MUTE OFF), 1 (MUTE ON)

How to set the grade

Use ASCII letters code to set the grade for setting data. Please refer to the table below for HEX code.

ASCII

'+'

'–'

'0'

'1'

'2'

'3'

'4'

'5'

'6'

'7'

'8'

'9'

HEX

2Bh

2Dh

30h

31h

32h

33h

34h

35h

36h

37h

38h

39h

[Example 1] Set the AUTO POWER ON to ON.

Sending commands	Status code from	Meaning
from the PC etc.	projector
30 30 41 50 4F 4E 31 0D		Command for setting the
'0' '0' 'A' 'P' 'O' 'N' '1' ' '		AUTO POWER ON to ON
	30 30 41 50 4F 4E 31 0D	Command received
	'0' '0' 'A' 'P' 'O' 'N' '1' ' '	(Command echo back)

The data code of CONTRAST and BRIGHTNESS is structured by the difference data of R from G, the main data and the difference data of B from G.

[Example 2] Set the difference data of R from G to +10, the setting main data to 0 and the difference data of B from to -5.

Sending commands		Status code from	Meaning
from the PC etc.		projector
30 30 50 2B 31 30 2B 30 30 2D 30 35 0D			Command for setting the
'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '	'		picture control
		30 30 50 2B 31 30 2B 30 30 2D 30 35 0D	Command received
		'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' '	(Command echo back)

[Example 3] The TINT was set to +10 when the setting status was confirmed.

Sending commands	Status code from	Meaning
from the PC etc.	projector
30 30 53 0D		Command to confirm
'0' '0' 'S' ' '		setting of TINT
	30 30 53 2B 31 30 0D	Command (setting of TINT
	'0' '0' 'S' '+' '1' '0' ' '	is +10) carried out

4