Mitsubishi Electronics SE1U user manual Using the menus, Displaying Information Status display

Remote Control

Using handy features (Continued)

■Displaying Information [Status display]

This displays information about the input signal, lamp use time, etc.

Press the button twice (or press the CALL button on the remote control once).

Using the menus

You can call up on-screen menus, and conduct a number of adjustments and settings using the operation buttons p.16 on the control panel (main unit side) and remote control.

■How to use the menus

The menu shown below is only for operation instructions and might be different from the

When the button is pressed once, the Setting display menu appears. Pressing it again displays information p.29 . The table below shows what kind of information is displayed. Press the button (or

Control panel

FAN TEMP LAMP POWER

SOURCE	ON / STANDBY
	ZOOM. +

actual display.

1.Start Display the Setting display menu

2. Select a Category

press the CALL or EXPAND OFF button on the remote control to serve the same purpose) again to dismiss the display.

	MENU/ENTER
VOL. -	VOL. +
KEYSTONE	AUTO POSITION
	ZOOM. -

“Yes”: displayed, “No”: not displayed

Select a category by using .

There are following three categories.

Image adjustment menu p.30

Default setting menu p.30

Displays the current adjustments of selected category.

Item shown with gray cannot be adjusted with the current input source.

Item	Description	Computer Y/PB/PR		Video	S-video
Source	Input source name	Yes	Yes	Yes	Yes
RGB signal mode	RGB input mode [Note 1]	Yes	No	No	No
H-resolution	Horizontal resolution (in bits)	Yes	No	No	No
V-resolution	Vertical resolution (in bits)	Yes	No	No	No
H-frequency	Horizontal sync frequency	Yes	No	No	No
V-frequency	Vertical sync frequency [Note 2]	Yes	No	No	No
Sync	Sync signal polarity [Note 3]	Yes	No	No	No
Signal format	Y/PB/PR signal format	No	Yes	No	No
Video mode	Color method of video signal	No	No	Yes	Yes
Lamp time	Time of lamp use [Note 4]	Yes	Yes	Yes	Yes

Display setting menu p.31

Pressto open the menu

3.Adjustments & Settingsof the selected category.

Item

Adjustment/Setting Value

5. To Finish

Finish via the Status display menu.

Operations

Version Firmware version [Note 5] Yes Yes Yes Yes

Notes

1: The mode of supported RGB signals p.38 is shown.

2: Same as the refresh rate of the computer signal.

3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].

4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be

used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000

These marks signify the items can be adjusted/set

by using .

These marks signify an item can be switched by

using .

This mark signfy that there are options.

Press to display a list of options.

To Status display

p.28

hours, consult with a store about getting aVLT-SE1LP replacement lamp (sold separately)

prepared.

5: [Version] shows the version of the projector’s internal control program. This version is

referred to for customer service, etc.

Notes

•	The displayed information will not be refreshed if the status changes. To refresh the
	information, dismiss the display, then display it again.
•	Conducting another operation while information is being displayed dismisses the

The figure shows a typical example. As the display may differ depending on the item, use the following pages as a reference.

These marks signify the items can be selected from

the list by using .

After an item is selected, apply it by pressing .

6. End

display.

4. Back

Notes

The menu disappears.

28

•Menu adjustments and settings are saved when the power is turned off via the ON/ STANDBY button. If the AC power cable is disconnected before this, or the power goes out, then the data will not be saved.

•You can also use the EXPAND OFF button on the remote control to dismiss the menu

display.

29