Mitsubishi Electronics SE1U user manual Before calling service personnel, Specifications, Others

Before calling service personnel

If you think something is wrong, check the followings before contacting customer service. Please see “Trouble indications” p.35 as well.

If This Happens		Check
No power	•	Is the AC power cord plugged in? Is it connected to the projector?
	•	Is the lamp cover loose? p.35
Power goes out	•	Is the ambient temperature high? p.35
during use	•	Is the air filter clogged? p.35
	•	Is the air intake or air exhaust blocked? p.35
No picture	•	Is the projector turned on? p.22
	•	Is the mute function on? p.26
	•	Is the brightness setting minimized? p.30
	•	Are the connections set up correctly? p.19
	•	Are all the connected devices functioning properly?
No audio	•	Is the projector turned on? p.22
	•	Is the mute function on? p.26
	•	Is the volume setting minimized? p.23
	•	Are the connections set up correctly? p.19
	•	Are all the connected devices functioning properly?
Picture not	•	Is the input signal supported by the projector? p.38 , p.39
displayed	•	Is the correct video mode selected? p.24
correctly	•	Is the correct signal format selected? p.24
	•	Is the selecting of computer or Y/PB/PR input correct? p.22
	•	Is there something generating an abnormal video signal, for
		instance the video tape?
Picture blurred	•	Is the lens dirty? p.33
Part of picture	•	Is the lens focus adjusted optimally? p.23
out of focus	•	Is the projection distance within the projector’s supported range? p.18
	•	Is the projector’s screen placement angle tilted too far? p.18
	•	Are the sharpness or sampling phase adjustments off? p.24 p.30
Image is dark	•	Are the brightness or contrast adjustments off? p.30
	•	Is the lamp nearing the end of its service life? p.30
Colors too light	•	Are the color, tint, R-level, G-level, or B-level adjustments off? p.30
Bad shading	•	Is the screen dirty?
	•	Is the lamp nearing the end of its service life? p.28
Remote control	•	Are the remote control’s batteries drained?
doesn’t work	•	Are the batteries inserted into the remote control correctly? p.17
	•	Is the remote control being used within the effective range? p.17
	•	Are there any obstructions between the remote control and projector?
	•	Are there any fluorescent or other bright lights shining at the
		projector’s infrared remote sensor?
Afterimages	•	This phenomenon is improved by keeping projecting an evenly
persist on the		bright image. (Such “image burn-in” phenomenon where
screen		afterimages persist on the screen may occur if a stationary image is
		kept displayed on the screen for a long time.)

Specifications

■List of general specifications

	Item			Specification
Type			LCD Projector
Model			SE1U
Rated Input			2.4 A
Rated Power Supply			100 - 240V AC, 50/60 Hz
Weight			2.1 kg
Outside Dimensions			303 ⋅ 84 ⋅ 206 mm (W ⋅ H ⋅ D)
(including protruding parts)
Cabinet material*			PC+ABS resin and ABS resin
Temperature, Humidity			Temp: +32°F (0°C) to +95°F (35°C);
(performance guaranteed)			Relative humidity: 30% to 70%
		Display method	3-panel transmission
		Panel size	0.5 type
LCD Panel		Drive system	TFT active matrix
		Picture	480,000 pixels (800H ⋅ 600V)
		elements
Projection Lens			F=1.8 f = 21.4mm
Light Source Lamp			High-pressure mercury lamp 130 W
Projection screen size			40-300 type
Projection distance			1.5-11.6 m
Speaker			1 W (Monaural)
terminal	COMPUTER terminal		Mini D sub 15 pin	RGB / Y/PB/PR (dual use)
	COMPUTER OUT terminal		Mini D sub 15 pin	RGB / Y/PB/PR (dual use)
	S-VIDEO terminal		Mini DIN 4 pin
Connection
	VIDEO terminal		RCA Pin Jack, 1 V (p-p), 75 Ω
	AUDIO terminal		3.5mm dia. stereo mini-jack, 1.5V (rms); 22 kΩ or more
	SERIAL terminal		Mini DIN 8 pin (RS-232C)

*Each plastic part displays the materials it is made from, in order to facilitate recycling after this product becomes no longer usable.

■Separately Sold Product

Replacement Lamp Model VLT-SE1LP

Note

•Design, specifications, etc. subject to change without notice for improvements, etc.

Others

36 37