Basic operation (continued)
Power-off
Use the following procedure to turn off the projector.
1.Press the POWER button on the control panel or the OFF button on the remote control.
•The message "POWER OFF? YES : PRESS AGAIN" appears on the screen.
•To cancel, press any button except the POWER button. (Some buttons on the remote control don’t function for can- cel.)
2.Press the POWER button on the control panel or the OFF button on the remote control within 10 seconds again.
•The lamp will go out and the STATUS indicator will start blinking.
•Though the lamp goes out at this second press of the POWER button (or OFF button), the air outlet fans continue operating for one minute to cool down the lamp. The STA- TUS indicator will stop blinking.
•After stopping the air outlet fans, if the temperature inside the set is still high, the temperature sensor detects it and then the air outlet fans may start again.
3.Unplug the power cord.
•The POWER indicator will go out.
•If the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10 min- utes with the power off. To light the lamp again, press the POWER button (or OFF button). If the lamp doesn’t light up immediately, repeat pressing the POWER button (or OFF button) two or three times. If it should still fail to light up, replace the lamp.
Notice:
•When storing the projector in the carrying case, the lens should face up.
Instant Shut Down
You can turn off this projector just by unplugging the power cord with- out pressing the POWER button.
•Don't shut down the projector while the STATUS indicator is blink- ing after the lamp lights up because the lamp's life may be short- ened.
•Don't turn the projector back on right after shutting it down because the lamp's life may be shortened. (Wait about 10 minutes before turning the projector back on.)
•Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without closing the menu, the setting data of the menu may not be saved.
AUTO POSITION button
When the image isn’t projected in the right position with COMPUTER selected as the input source, follow the procedure below.
1.Project a bright image such as the "Recycle Bin" window on the full screen.
2.If the screen saver is running, turn it off.
3.Press the AUTO POSITION button.
•If the image is still not in the right position, adjust the image position using the SIGNAL menu. See page 19.
Volume from the speaker
Press the VOLUME + or
The volume control bar will appear on the screen.
VOLUME | 10 |
•The volume control bar will disappear about 10 seconds after the VOLUME button is released.
•The VOLUME buttons don’t function while the menu selection bar or the menu is being displayed.
•When a
AV mute
The video and audio signals are temporarily muted when the MUTE button is pressed. To cancel muting, press the MUTE button again.
ANAMORPHIC mode
When playing DVD discs containing data of letterboxed image, press the 16:9 button. Exit the ANAMORPHIC mode, by pressing the 16:9 button again.
Important:
•When a letterboxed image is kept displayed for a long time before displaying 4:3 image, the afterimages of the black bars may appear on the 4:3 image screen. Consult your dealer in this case.
Caution:
•After using the projector, wait one minute for the air outlet fans to stop. Then unplug the power cord from the wall outlet.
•The lamp can’t be lit again for one minute after turned off for safety purpose. It will take another one minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator goes out, and then press the POWER button.
•The air outlet fans rotate faster as the temperature around the pro- jector rises.
•When the temperature around the projector rises high, the sign "TEMPERATURE!!" blinks red on the screen. If the temperature stays high, the lamp will go out automatically.
Important:
•Do not display a still picture for a long time because the afterim- ages may persist on the screen.