Mitsubishi Electronics XD470U Adjustment of the image from the computer, Simple adjustment method

Page 19

Adjustment of the image from the computer

Adjustment of the image from the computer

This projector adjusts the format of the video signal supplied from the computer. However, sometimes images are not projected correctly owing to the type of the computer used. When the image from the computer isn’t projected correctly, press the AUTO POSITION but- ton. (See page 14.) If the image isn’t projected correctly yet, adjust the image from the computer using the menu.

Simple adjustment method

1.	Select HORIZ. POSITION in the SIGNAL menu.
2.	Press the W or X button to adjust the horizontal start position
	(or the left side of the image).
3.	Select TRACKING in the SIGNAL menu.
4.	Press the W or X button to adjust the horizontal end position (or
	the right edge of the image).

ENGLISH

opt.

SIGNAL

XGA60

5.	Repeat steps 1 to 4 for optimum adjustment results.
6.	Select VERT. POSITION in the SIGNAL menu.
7.	Press the W or X button to adjust the vertical start position (or
	the upper edge of the image).

	HORIZ. POSITION		0

	VERT. POSITION		0

	FINE SYNC.		0

	TRACKING		0

	COMPUTER		RGB
	RRGGBB INPUT		RGB

	SET UP		7.5%

	HOLD		ON

	USER		OK

To move the image horizontally :

Adjust HORIZ. POSITION in the SIGNAL menu. Press the X button to move the image to the left. Press the W button to move the image to the right.

To move the image vertically :

Adjust VERT. POSITION in the SIGNAL menu. Press the X button to move the image upward. Press the W button to move the image downward.

When the image flickers or the image is out of focus :

Adjust FINE SYNC. in the SIGNAL menu.

When the top part of the image flags :

Change the setting of HOLD in the SIGNAL menu. Select ON , press the ENTER button, and adjust BEGIN or END to minimize the flagging.

USER

	CLAMP	0
	POSITION

	CLAMP WIDTH	1

When wide strips appear :

Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL - USER menu.

Important:

Do not change any of the settings in the SIGNAL-USER menu for normal use.

EN-19

Image 19

Contents ENGLISH Please read it before using your projectorMODEL This User Manual is important to youREFER SERVICING TO QUALIFIED SERVICE PERSONNEL When using the projector in Europe COMPLIANCE NOTICECAUTION TO REDUCE THE RISK OF ELECTRIC DO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDEImportant safeguards ContentsDeclaration of Conformity Trademark, Registered trademarkImportant safeguards Do not look into the air outlet grilles when projector is operating Do not keep using the damaged projectorDo not look into the lens when the projector is operat- ing Do not unplug the power cord during operationControl panel OverviewTerminal board Bottom side Remote controlReception angle vertical Remote controlBattery installation Operation range of the remote controlFront projection, ceiling mounting InstallationLayout of the projector Front projectionProjector + AV device Basic connectionsProjector + DVD player or HDTV decoder For monitor connection Projector + ComputerFor computer with Mini D-SUB For analog connectionAfter using the projector Adjustment of the projection angleUsing the adjustment feet front Using the adjustment feet rearZOOM Power-onBasic operation FOCUSInstant Shut Down Power-offVolume from the speaker Basic operation continuedXGA60 INSTALLATIONMenu operation Basic operationXGA60 2 INSTALLATION1 IMAGE XGA604 SIGNAL 3 FEATURE5 SIGNAL - USER No need to adjust in normal use To adjust the detail and clarity of the image Image adjustmentImage adjustment To adjust the red-green color balance of the imageWhen the top part of the image flags Adjustment of the image from the computerSimple adjustment method When the image flickers or the image is out of focusPage-up and page-down Advanced featureStill To resume the motion in the imageTo cancel the password function Password functionTo enable the password function Interval of lamp replacement Lamp replacementCause and solution TroubleshootingImages aren’t projected on the screen ProblemImages aren’t projected correctly Troubleshooting continuedOthers MaintenanceCleaning of the projector and the ventilation slots Cleaning of the lensNormal condition IndicatorsAbnormal condition EN-27 SpecificationsReplacement part Specifications continuedConnectors Dimensional drawings unit mmSpecification of RGB signals in each computer mode of the projector MITSUBISHI Projector Contact Information MITSUBISHI ELECTRIC CORPORATION1 Zusho Baba, Nagaokakyo-City, Kyoto Japan