Mitsubishi Electronics LVP-X400U user manual Lamp replacement, Interval of the lamp replacement

Page 23

Lamp replacement

The lamp is designed to project the image on the LCD panels. When the lamp no longer functions, replace it with a new one.

Caution:

Do not remove the lamp immediately after using the projector, you may get burned because of the high temperature of the lamp.

When you replace the lamp, press the power button to power off, then wait for 120 seconds in stand-by mode to allow the lamp and LCD panels to cool. Turn off the main switch, unplug the power cord from the outlet, and wait one hour so that the lamp is cooled to the touch.

Do not remove the lamp except for replacement. Careless treatment can cause injury or fire.

Do not touch the lamp element directly. It may break and cause you to injure or burn yourself.

Be sure not to drop the lamp lid screw into the pro- jector. Also be sure not to insert metal or any flam- mable objects, it may cause fire or electric shock. If any objects are inserted, please unplug and contact your dealer.

Install the lamp securely, failure may cause a fire.

1. Reverse the projector gently.

(a)

2.Loosen the screws of the lamp lid

(a) using a phillips screwdriver (+).

3.Remove the lamp cover in the direction of the arrow as indi-

9.Tighten up the screws (b) using a phillips screw- driver (+).

10.Tighten up the screws of the lamp lid using a phillips screwdriver (+).

How to reset the operation time meter

Plug in the power cord, switch on the projector, and reset lamp time by pressing the $, % and POWER buttons simultaneously.

Important:

If the 3 buttons was not pressed at the same time, the lamp time may not be reset.

Please confirm the TEMP indicator illuminates about 2 seconds and the lamp time has been reset.

The projector will not turn on if you do not secure the lamp lid.

You must reset the operation time meter after you replace the lamp.

Do not reset the operation time meter unless the lamp has been replaced.

Caution:

Do not spill liquid on the lamp or place it near flam- mable objects or where children can touch it. Oth- erwise, it could cause injury or fire.

Be sure that the projector guide is firmly inserted between the right and left lamp guides.

Interval of the lamp replacement

The interval of the lamp replacement about 1,500 hours of consecutive use. Replacement span may differ ac- cording to operating environment, and may be shorter than 1,500 hours. Decreases in luminescence and/or color brightness will indicate that the light source lamp needs to be replaced. When lamp operation time ex- ceeds 1,000 hours, the indicator will flash alternately

ENGLISH

cated.

4. Loosen screws (b) using a phillips screwdriver (+), and remove them.

5. Pull up the handle.

(b)

between green and red (while the lamp is in operation; when the lamp is not in operation, the indicator will appear red only). When the lamp has been used for about 1,400 hours, the message “LAMP!!.” will appear on the screen for one minute. When the lamp has been used for about 1,500 hours, the projector will automati- cally shut off for safety and the power indicator light will be red. The projector cannot be used until the lamp has been replaced and operation timer has been reset.

Caution:

6. Hold onto the projector by the handle as you pull out the lamp.

Once the lamp has been removed,

do not spill liquid on it, place it near flammable objects or where chil-

dren can touch it. Otherwise, it will cause injury or fire.

7.Insert the new lamp securely into the projector body in the right direction.

8.Put the handle back to the holding point.

• Make sure that the handle is locked.

The lamp is fragile. If broken, be careful not to cut yourself with glass fragments.

The replacement span of the lamp depends on the environment. For replacement lamps, please con- tact your dealer.

The projector automatically shuts off when the lamp is used up in about 1,500 hours and cannot be used until the lamp is replaced and the internal timer is reset.

EN – 23

Image 23
Contents X400 English Français Deutsch Italiano EspañolCompliance Notice When using the projector in EuropeContents Important safeguards Compliance Notice of Industry Canada Terminal board OverviewAbout laser beam Bottom side Remote controlUsing the wired remote control Using the remote controlBattery installation Operation area for wireless control systemFront projection, ceiling mount InstallationOrientation of the projector Front projectionProjector + DVD player or Hdtv decoder Basic connectionsProjector + AV equipment About DDC For DVI connection For using MacintoshProjector + Personal computer For computer with DVI terminalGetting ready for projection Adjusting the angle of projectionPreparing the projector for operation Button To operate projector power onAuto Position AV mute To operate projector power on ContinueVolume from the speaker Turning off the projectorBasic operation Menu operationOption InstallationMenu operation PictureSignal User memory for signal settingColor matrix Picture adjustmentAdjusting the image Color temperatureAdjustment from personal computer XGA85 Picture adjustmentStill Advanced features for presentationExpand Picture in Picture PinPProjector + computer with PS/2 connector Advanced features for presentationMouse remote control Projector + computer with USB connectorHow to reset the operation time meter Lamp replacementInterval of the lamp replacement Cleaning the lens MaintenanceCleaning the air-filter Cleaning the projector and the ventilation slotsProblems Cause Possible Solutions TroubleshootingAbnormal condition IndicatorsNormal condition Rated input LCD panels SpecificationsReplacement part Option / Not included in the box SpecificationsConnectors Dimensional drawings mm871D293A40
Related manuals
Manual 34 pages 11.69 Kb