Mitsumi electronic HC3800 Auto Position button, When connecting to a notebook computer

Page 24

Viewing computer images (continued)

7.Adjust the image size by turning the zoom ring.

• If necessary, adjust the focus and zoom again.

To stop projecting:

8. Press the POWER button on the projector or the OFF ( ) button on the remote control.

•A confirmation message is displayed.

•To cancel the procedure, leave the projector for a while or press the MENU button.

9. Press the POWER button on the projector or the OFF ( ) button on the remote control again.

•The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS indicator blinks green.

10.Wait about 90 seconds.

•During this period of 90 seconds in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.

•The lamp can’t be lit again for 1 minute after turning off the projector for safety purpose. It will take another 1 minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator goes out, and then press the POWER button.

•The air outlet fans rotate faster as the temperature around the projector rises.

•Do not unplug the power cord while the STATUS indicator is blinking. Unplugging the power cord immediately after use may cause a lamp breakdown.

•Though the fan makes loud sounds during cooling, such symptom is not a malfunction.

11.Unplug the power cord from the outlet.

•The POWER indicator will go out.

•If the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10 minutes with the power off. To light the lamp again, press the POWER button. If the lamp doesn’t light up immediately, repeat pressing the POWER button two or three times. If it should still fail to light up, replace the lamp.

•Cover the lens with the lens cap to protect it from dust.

AUTO POSITION button

When the image supplied from the computer is displaced, carry out the following procedure.

1.Display a bright image (such as a full-screen display of the Recycle Bin window). . When the screen saver has been enabled, disable it.

. Press the AUTO POSITION button.

The projector automatically makes optimum positional settings for the input signal.

•If the image is not projected in the correct position even after you press the AUTO POSITION button several times, change the settings in the SIGNAL menu to put the image in the correct position. (See page 34.)

•When you carry out this procedure with a dark image, the image may be displaced.

When connecting to a notebook computer:

When the projector is connected to a notebook computer, images may not be projected in some cases. In such cases, set the computer so that it can output signals externally. The setting procedure varies depending on the type of the computer. See the instruction manual of your computer.

Example of the setting procedure for external output

Press the [Fn] key and any of the keys [F1] to [F12] at the same time. (The key to be pressed depends on the type of the computer you use.)

Setting of the resolution

If the resolution of the computer doesn’t match with that of the projector, projected images may be obscured. Ensure that their resolutions are the same (see page 46). For the method to change the output resolution of the computer, contact the manufacturer of the computer.

EN-24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents HC3800 When using the projector in Europe Risk of Electric Shock Do not OpenContents Important safeguards Important safeguards Inserting the batteries into the remote control Removing the batteries from the remote controlPreparing your projector What’s included in the boxPreparing your projector OverviewControl panel Terminal panelRemote control Using the picture quality adjusting buttonsBottom side Using the remote control Operational range of the remote controlReception angle Setting up your projector Setting up the screenWhen the aspect ratio of the screen is Screen size and projection distanceSetting up your projector When the aspect ratio of the screen is 2.351 CinemaScopeWhen the aspect ratio of the image is When fine streaks are seen on projected images When projected images are distorted to a trapezoidWith the Installation menu See page 26 for menu setting To cancel the menuInstallation Front projection, ceiling mountingRear projection Trigger terminalConnecting the projector to video equipment Viewing video imagesBasic home theater system connection PreparationConnecting to a video player, etc Connecting to a DVD player or Hdtv decoderWhen a TV tuner or VCR is connected Viewing video imagesConnecting to video equipment having a Hdmi terminal Connection for video equipment having an Hdmi terminalPlugging in the power cord Projecting images To stop projecting Setting the aspect ratio ZOOM1 ZOOM2 Stretch ANAMORPHIC1 ANAMORPHIC2How to change the settings With the remote controlWith the Feature menu See page 26 for menu setting Connecting the projector to a computer Plugging the power cordViewing computer images About DDCViewing computer images ComputerWhen connecting to a notebook computer Setting of the resolutionExample of the setting procedure for external output Auto Position buttonFeature Signal Keystone Lamp Mode Menu operationHow to set the menus Available settings in the menusSetting Function Menu operationInstallation menu Feature menu Signal menu User menuTo store the settings To enable the stored image quality settingsAV memory Information menuAdjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint How to Use BrilliantColorTMAdjusting projected images To adjust the tone of white Color TempAbout color temperature To enable the stored color temperatureHow to Use Color Management To adjust the ratio of change in brightness Gamma ModeBlue Magenta RED HighTo enable the stored gamma mode To adjust the vertical positionLPF Progressive filter Advanced features Password functionTo enable the password function To cancel the password functionInterval of lamp replacement Replacing the lampWhen the projector is mounted to the ceiling Replacing the lampTo replace the lamp Reset of the lamp operation time Maintenance Cleaning of the projector and the ventilation slotsCleaning of the lens Troubleshooting No image appears on the screen Problem SolutionTroubleshooting Images are not displayed correctly Problem SolutionOthers Problem Solution EN-43 Indicators Status Condition Possible SolutionNormal condition Abnormal conditionSpecifications Dimension drawings unit mmSpecifications Connectors Replacement part option/not included in the boxComputer IN/COMPONENT Video VLT-HC3800LPMitsubishi Electric Corporation

HC3800, HC3800 specifications

The Mitsumi Electronic HC3800 is a versatile and innovative device that plays a crucial role in enhancing connectivity and signal transmission in various electronic applications. Designed to meet the demands of modern technology, the HC3800 stands out due to its robust features, cutting-edge technology, and reliable performance.

One of the main features of the HC3800 is its high-speed data transmission capabilities. It supports advanced protocols that allow for quick and efficient communication between devices. This is particularly important in applications such as telecommunications, automotive systems, and industrial automation where speed and reliability are paramount. The HC3800 ensures minimal latency, enabling real-time data processing and response.

Another highlight of the HC3800 is its compact and efficient design. With a small footprint, it can easily be integrated into a wide range of devices, from handheld gadgets to larger industrial equipment. This versatility makes it a preferred choice for manufacturers looking to optimize space without compromising on performance.

The HC3800 employs advanced modulation techniques, which enhance signal integrity and reduce interference. This is critical in environments where electromagnetic interference (EMI) can disrupt communications. By utilizing robust error detection and correction algorithms, the HC3800 maintains high levels of data integrity, ensuring that information is transmitted accurately even in challenging conditions.

Moreover, the Mitsumi HC3800 boasts an impressive power efficiency profile. It is engineered to operate effectively at lower power levels, making it suitable for battery-operated devices. This not only extends the longevity of devices using the HC3800 but also complies with green technology initiatives aimed at reducing energy consumption.

The technology within the HC3800 is continually evolving, ensuring compatibility with future advancements. Mitsumi's commitment to research and development means that users can expect regular updates and improvements in performance features. Additionally, the HC3800 provides extensive support for a wide array of interfaces, making it adaptable to various system architectures.

In conclusion, the Mitsumi Electronic HC3800 is a state-of-the-art component that combines high-speed data transmission, compact design, superior signal integrity, and energy efficiency. Its features make it an ideal choice for a multitude of applications across different industries, ensuring that users benefit from enhanced connectivity and reliable performance in their electronic systems. Whether it's for personal or industrial use, the HC3800 continues to meet and exceed market demands while shaping the future of electronic connectivity.
Top Page Image Contents