Mitsubishi Electronics HC3000 user manual Trigger terminal, EN-11, To cancel the menu

Page 11

Front projection, ceiling mounting

For ceiling mounting, you need the ceiling mount kit designed for this projector. Ask a specialist for instal- lation. For details, con- sult your dealer.

•The warranty on this projector does

not cover any damage caused by use of any non- recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.

•When using the projector mounted on the ceiling, set IMAGE REVERSE in the INSTALLATION menu to MIRROR INVERT. See page 25.

•When the projector is mounted on the ceiling, im- ages may appear darker than those projected in the case of tabletop mounting. This isn't a product malfunction.

•Ask your installation specialist to provide an A/C power switch. When you do not use the projector, be sure to shut down the main power by the switch.

•Do not install the projector where the exhaust vents are exposed to air emitted by an air conditioning. Such installation may cause a breakdown.

•Do not install the projector near a fire alarm because it emits hot air from its exhaust vents.

Rear projection

Ask a specialist for in- stallation. For details, consult your dealer.

•For rear projec- tion, set IMAGE REVERSE in the

INSTALLATION menu to MIRROR. See page 25.

Caution:

•Placing the projector directly on a carpet impairs ventilation by the fans, causing damage or failure. Put a hard board under the projector to facilitate ventilation.

•Place the projector at least 50 cm (or 20 inch) away from the wall to prevent the air inlet grille and the air outlet grilles that emit hot air from being blocked.

•Do not use the projector in the following locations and manners, which may cause fire or electric shock.

•In a dusty or humid place.

•In a sideways or upside-down position.

•Near a heater.

•In an oily, smoky, or damp place such as a kitchen.

•In direct sunlight.

•Where the temperature rises high, such as in a closed car.

•Where the temperature is lower than +41ºF (or +5ºC) or higher than +95ºF (or +35ºC ).

TRIGGER terminal

The TRIGGER terminal on the rear of the projector is a terminal that outputs a 12 V signal to control an externally connected device (electric screen) when images are projected.

HDMI IN

 

COMPONENT VIDEO IN

 

 

S-VIDEO IN

SERIAL

USB

 

 

TRIGGER

VIDEO IN

TRIGGER

To externally connected device

Ring (NC)

Tip (12 V)

 

(ground 0 V)

To use the TRIGGER terminal, set TRIGGER OUT to ON in the INSTALLATION menu. (The factory default is OFF.) Use the following steps to change the setting.

With the INSTALLATION menu: (See page 24 for menu setting.)

1. Display the INSTALLATION menu.

2.

Select TRIGGER OUT by pressing the or but-

 

ton.

3.

Select ON by pressing the or button.

To cancel the menu:

4. Press the MENU button.

Caution:

•Do not use the signal output from the TRIGGER terminal as a power for other devices.

•Do not link the TRIGGER terminal with an audio terminal of other device because that device may be damaged.

•The rated current for the TRIGGER terminal is 200 mA. If you use a current exceeding this rating, a failure may occur.

•For information about electric screens, please con- tact screen manufacturers.

ENGLISH

EN-11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents HC3000 EN-2 When using the projector in EuropeContents EN-4 Important safeguardsEN-5 Cables Checking accessoriesInserting the batteries into the remote control Preparing your projectorEN-7 OverviewControl area Terminal panel Bottom side Remote controlUsing the picture quality adjusting buttons Preparing your projector ContinueEN-9 Using the remote controlOperational range of the remote control Reception angleAdjusting the projection angle Setting up your projectorSetting up the screen Basic setupEN-11 With the Installation menu See page 24 for menu settingTo cancel the menu Trigger terminalEN-12 Setting up your projectorWhen the aspect ratio of the screen is Screen size and projection distanceEN-13 Connecting the projector to video equipmentViewing video images Basic home theater system connectionViewing video images Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder When a TV tuner or VCR is connectedConnection for video equipment having a DVI-D terminal EN-15Connection for video equipment having a Hdmi terminal EN-16 Plugging in the power cordEN-17 Projecting imagesFollowing cases When projected images are distorted to a trapezoidTo stop projecting EN-18EN-19 Setting the aspect ratioHow to change the settings Iris buttonEN-20 Connecting the projector to a computerPlugging the power cord Viewing computer imagesEN-21 Projecting imagesAuto Position button When connecting to a notebook computerExample of the setting procedure for external output Viewing computer imagesEN-23 Menu operationEN-24 How to set the menusAvailable settings in the menus Menu operationEN-25 Installation menuFeature menu EN-26 AV memoryTo sharpen or soften the projected image Sharpness Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintTo adjust the ratio of change in brightness Gamma Mode Adjusting projected imagesTo adjust the tone of white Color Temp About color temperatureEN-29 To adjust the vertical positionTo cancel the password function Advanced featuresPassword function To enable the password functionCleaning the filter Using filterInstallation CleaningEN-32 Interval of lamp replacementReplacing the lamp To replace the lamp Cleaning of the projector and the ventilation slotsCleaning of the lens Reset of the lamp operation timeEN-34 TroubleshootingNo image appears on the screen Problem SolutionImages are not displayed correctly No image appears on the screen Problem SolutionProblem Solution EN-35EN-36 TroubleshootingOthers Problem Solution EN-37 IndicatorsNormal condition Abnormal conditionEN-38 Dimension Drawings unit mmSpecifications EN-39 ConnectorsReplacement part Option / Not included in the box Mitsubishi Projector Contact Information
Related manuals
Manual 40 pages 11.21 Kb

HC3000 specifications

The Mitsubishi Electronics HC3000 is a cutting-edge projector designed to deliver high-quality visuals for both home theater enthusiasts and professional presentations. Known for its exceptional image clarity and versatility, the HC3000 stands out in the crowded market of digital projection.

One of the key features of the HC3000 is its superior resolution capability. With support for Full HD (1920 x 1080), it ensures that images are sharp and vibrant, making it ideal for cinematic experiences and detailed presentations. The high brightness level, which reaches up to 3000 ANSI lumens, allows for clear visibility in various lighting conditions, whether in a dimly lit home theater or a well-lit conference room.

The HC3000 employs advanced DLP (Digital Light Processing) technology, which enhances color accuracy and reduces the possibilities of rainbow effects that can occur in some projection technologies. This DLP technology is complemented by Mitsubishi's proprietary color wheel, which enhances color reproduction, providing deep blacks and rich colors that make images pop.

Another standout characteristic is its flexible connectivity options. The HC3000 includes multiple input terminals, including HDMI, VGA, and composite inputs, making it compatible with a range of devices such as Blu-ray players, gaming consoles, and laptops. This multitude of options ensures that users can easily integrate the projector into their existing systems and switch between different sources without hassle.

Portability is another strength of the HC3000. Weighing in at a manageable size, it can be transported easily, making it a great option for business professionals who need to present on the go. Its compact design does not sacrifice performance for size, maintaining high-quality output even in a portable format.

Additionally, the HC3000 incorporates a robust cooling system designed to extend the life of the projector's lamp. This feature not only enhances durability but also minimizes operational noise, allowing for an immersive viewing experience without distracting sounds.

In summary, the Mitsubishi Electronics HC3000 is a versatile and high-performing projector, offering Full HD resolution, advanced DLP technology, excellent connectivity options, and portability. Whether for home entertainment or professional use, it delivers outstanding image quality, making it a popular choice among consumers seeking reliability and performance.
Top Page Image Contents