Mitsubishi Electronics MLM400 user manual Important Information

Page 3

Important Information

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950.

FCC Information

1.Use the attached specified cables with the MLM300 (L30HV201) color monitor so as not to interfere with radio and television reception.

(1)Please use the supplied power cord or equivalent to ensure FCC compliance.

(2)Please use the supplied shielded video signal cable, 15-pin mini D-SUB to 15-pin mini D-SUB.

2.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful: ”How to Identify and Resolve Radio-TV Interference Problems.“ This booklet is available from the U.S. Government Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

1

Image 3
Contents MLM300 Table of Contents Canadian Department of Communications Compliance Statement Important InformationSafety Precautions and Maintenance Recommended UseErgonomics Contents To avoid falling down Ambient temperature should be less than 40 deg CAttaching LCD Options Lay the screen face downActs as SET button with on-screen menu Switches the audio mute ON/OFFRocker Switch for the main power on/off Control PanelTerminal Panel To output the audio signal from the Audio in 3 jackTo output the audio signal from Audio 1, 2 or 3 jack Parts Name and FunctionsWireless Remote Control RGB2DVD/HD Video Avoid exposure to heat and steam 30o 30o Operating Range for the Remote ControlHandling the remote control Other than to install the batteries, do not open the remoteSetup Procedure For PC Audio Cable Wiring DiagramConnections Before making connectionsTo audio output Connecting the LCD Monitor to a PCConnecting to a Macintosh Computer To DVI output Connecting to a Computer with a Digital OutputRCA Connecting to a VCR or Laser Disc PlayerConnecting to a DVD Player Connecting to a Stereo Amplifier Using the remote control Pressing the Main Power Switch Pressing the power buttonBasic Operation On-Screen Menu Controls -Computer On-screen Menu Controls Auto Adjust Audio ResetConfiguration Auto SetupLanguage Power SaveOFF Timer Auto BrightnessBass On-screen Menu Controls -DVD & HDConfiguration Reset Treble On-screen Menu Controls -AV InputTint Noise ReductionOFF Timer menu, you can select how Selecting PIP Reset allows you to reset all PIPSettings to factory default position Restore to factory defaultsColor System Using the LCD with a Personal ComputerPC Using the LCD with a Personal Computer Features Troubleshooting References Input Signal PC Input Video SpecificationsLimited Warranty MLM300 L30HV201 Mitsubishi MLM300