Mitsubishi Electronics ES100, EX100 user manual Menu operation, Basic operation

Page 15

Menu operation

IMAGE

INSTALLATION

CONTRAST

BRIGHTNESS

CineRichColor *1

sRGB

COLOR TEMP. *1

COLOR

*1

TINT

*1 *2

SHARPNESS *2

GAMMA MODE *1

AUTO POWER ON

±30

 

±30

 

AUTO, 0 - 10

 

ON, OFF

 

STANDARD

CONTRAST R

LOW

CONTRAST B

HIGH

BRIGHTNESS R

USER

BRIGHTNESS B

±10

±10

±5

AUTO, DYNAMIC, STANDARD, THEATER

ON , OFF

±30

±30

±30

±30

ENGLISH

FEATURE

AUTO POWER OFF

SPLASH SCREEN

BACK COLOR

LAMP MODE

IMAGE REVERSE

MENU POSITION

CINEMA MODE *4 VIDEO SIGNAL

ANAMORPHIC

PASSWORD FUNCTION

LANGUAGE

RESET ALL

OFF, 5,

10,

15,

30,

60 min

 

 

 

 

 

 

 

 

 

 

 

 

ON , OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BLUE, BLACK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STANDARD, LOW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OFF, MIRROR, INVERT, MIRROR INVERT

 

 

 

(These items are not available when the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 (Upper left), 2(Lower right)

 

 

 

 

 

 

input source is COMPUTER.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO , OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

AUTO , NTSC , PAL , SECAM , 4.43NTSC , PAL-M , PAL-N , PAL-60

 

 

ON , OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MENU ACCESS

 

 

 

LOCK

 

 

OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UNLOCK

 

 

OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

, English, Español, Deutsch, Français, Italiano,

,

,

 

,

OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIGNAL

HORIZ.POSITION

VERT.POSITION

FINE SYNC. *3

TRACKING *3

COMPUTER INPUT *3

SET UP

HOLD *3

USER *3

 

0 - 999

*5

 

 

 

 

 

0 - 999

*5

 

 

 

 

 

0 - 31

 

 

 

 

 

 

 

 

 

 

0 - 9999

*5

 

 

 

 

 

RGB, YCBCR / YPBPR

 

 

 

 

OFF / 3.5% / 7.5%

 

 

 

 

ON

 

 

 

 

 

BEGIN

 

OFF

 

 

 

END

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

 

 

 

 

 

CLAMP POSITION

 

 

 

 

 

 

 

 

 

 

CLAMP WIDTH

 

 

 

 

 

 

 

 

 

 

 

 

 

0 - 15

0 - 15

0 - 63

1 - 63

*5

*5

*5

*5

*1: Not available when sRGB is set to ON.

*2: Not available with certain signals.

*3: Not available when the source is a VIDEO or S-VIDEO signal.

*4: Available only when the input signal is TV60, 480i.

*5: Setting range differs depending on the input signals.

Basic operation

Several settings can be adjusted using the menu. Example : Auto power off time setting

1. Press the MENU button.

4. Press the ￿ or ￿ button to select AUTO POWER OFF.

 

 

AUTO POWER

OFF

 

 

ON

 

 

AUTO POWER

OFF

 

 

OFF

 

 

 

 

opt.

IMAGE

XGA60

5. Press the ￿ or ￿ button to adjust the auto power off time.

2. Press the ￿ or ￿ button to select INSTALLATION.

opt.

XGA60

INSTALLATION

3. Press the ENTER button (or ￿ button).

opt.

XGA60

INSTALLATION

AUTO POWER

OFF

ON

 

 

 

AUTO POWER

OFF

 

 

OFF

 

 

AUTO POWER

OFF

 

 

ON

 

 

AUTO POWER

30 min

 

 

OFF

 

 

 

 

6.Exit the menu by pressing the MENU button sev- eral times.

Important:

When the button doesn't function, unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try again.

After selecting the items marked with , press the ENTER button.

EN - 15

Image 15
Contents EX100 ES100 Compliance Notice When using the projector in EuropeContents Important safeguards Never remove the cabinet Do not modify the projector Do not keep using the damaged projectorDo not look into the lens when the projector is oper- ating Place of installationOverview Control panelTerminal board Adjustment foot Front Lamp cover Adjustment feet Rear Bottom side Remote controlReception angle vertical Remote controlBattery installation Operation range of the remote controlFront projection InstallationLayout of the projector Rear projectionBasic connections Projector + AV deviceProjector + DVD player or Hdtv decoder For computer with Mini D-SUB Projector + ComputerFor Macintosh About DDCPreparation for projection Adjustment of the projection angleAfter using the projector PreparationBasic operation Power-onAuto Position button Power-offVolume from the speaker Anamorphic modeBasic operation Menu operationMenu operation Signal User No need to adjust in normal use About color temperature Image adjustmentImage adjustment Color temperatureSimple adjustment method Adjustment of the image from the computerConnection Advanced featuresStill Page-up and page-downPassword function To enable the password functionTo cancel the password function Interval of lamp replacement Lamp replacementTroubleshooting Problem Cause and solutionImages arent projected on the screen Images arent projected correctly TroubleshootingCleaning of the projector and the ventilation slots Cleaning of the lensOthers Normal condition IndicatorsKensington Lock SpecificationsSpecifications Replacement partCGA84 Mitsubishi Electric Corporation