PLUS Vision U7-132h General Operation, Input Selection, Automatic Adjustment of Analog RGB

Page 27

General Operation

This section describes the use of direct operation with the main unit or remote control buttons.

For information about operation using the menu, see "Menu Operation Method" on Page E-27 and the various items on Pages E-44 to E-57.

Input Selection

Select the input signal to be projected. Press the SOURCE button on the projector or the RGB or VIDEO button on the remote control unit.

When one of the buttons is pressed, a menu for selecting the source ap- pears. Use the SELECT ￿ and ￿ buttons or the SOURCE, RGB and VIDEO buttons to select the desired source, then press the ENTER button.

When the “Auto Source” function is set to “On”, the input signals are searched for automatically in sequence, but the next input signal is not detected while the input signal selection menu is displayed.

SOURCE button

DVI → RGB → Image Viewer → Network → Video → S-Video U7-137 only

RGB button

DVI → RGB → Image Viewer → Network

U7-137 only

VIDEO button

Video → S-Video

Note

*When you do not operate source selection, the projector will assume the input selec- tion condition that was previously used.

*See "Auto Source" on Page E-51 for information about the Auto Source on and off conditions.

*When the input format has been switched, you may be required to reconnect the input signal.

SOURCEAUTO

MENU

 

QUICK

 

 

MENU

STANDBY

 

LASER

RGB

VIDEO

AUTO

MENU

 

QUICK

 

 

Q

ENTER

 

R-CLICK/

 

CANCEL

FREEZE

MUTE

TIMER

12

VOL ZOOM

34

Automatic Adjustment of Analog RGB

This procedure automatically adjusts the position, screen size, vertical stripes and colors of the analog RGB or DVI analog input signals being projected.

Normally, this function is adjusted automatically at the time of signal selection.

Main unit operation/Remote control operation: Press the AUTO button. (This

will not function while the menu or the quick menu is displayed.) A press of the AUTO button starts the automatic adjustment.

Note

*If the display position is shifted, vertical lines appear on the picture, or the projection is not good even after using automatic adjustment, please perform image adjustment manually. See "Picture Adj. / Fine Picture / H Position / V Position " on Page E-44.

*If the position is off or there are dark vertical bands on the picture, press the AUTO button with the screen as bright as possible (make the screen as bright as possible by for example displaying the trash window over the entire screen). If the problem per- sists after pressing the AUTO button several times, set manually at the “Picture Ad- justment” menu.

*When the image extends beyond the boundaries of the screen or is smaller than the screen, set Aspect to "Auto". See "Aspect" on Page E-49.

SOURCEAUTO

MENU

 

QUICK

 

 

MENU

STANDBY

 

LASER

RGB

VIDEO

AUTO

MENU

 

QUICK

 

 

Q

ENTER

 

R-CLICK/

 

CANCEL

FREEZE

MUTE

TIMER

12

VOL ZOOM

34

E-27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents U7-137 U7-132/U7-132h DOC Compliance Notice PrecautionsLamp Replacement InstallationPower Supply CleaningMajor Features Table of Contents Miscellaneous Adjustments and SettingsTable of Contents Menu OperationsVideo cable RCA pin plug, 2 m / 6.6 feet Checking the Supplied AccessoriesRGB signal cable Mini D-sub 15-pin, 2 m / 6.6 feet DVI/Mini D-Sub 15-pin conversion adapter 18 cm / 0.59 feetCable pocket Checking the Supplied AccessoriesStorage case for projector and accessories USB cable type A, 2 m / 6.6 feetBuilt-in Security Slot Names of the Main Unit PartsNames of the Main Unit Parts Precautions Handling of the Remote Control Names of the Remote Control PartsPreparing the Remote Control Remote Control RangeInserting the Batteries Procedure Up to Projecting to the Screen Screen Size and Projection Distance Placement GuidePersonal Computers with a DVI Connector Connections with Personal ComputerDVI-D cable Available as an option. Order code Personal Computers with a Mini D-Sub 15-Pin Connector Connecting Personal Computers and Video EquipmentRGB signal cable Supplied item Manufacturer Model Key To Output the External Output Signal of a Notebook ComputerVideo cable Suppled item Video cable Supplied item Connections with Composite SignalsVideo Equipment with Video Connectors Video Equipment with S-VIDEO ConnectorsConnections with Component Signals Supplied item Connections with Audio ConnectorsAudio cable Supplied item Audio conversion adapterConnections with the RGB OUT Connector Switch on the projector power OperatingButton on main unit Cursor Power Cable Connections and Switching the Power On/OffPress the Enter button to set This completes the selection of the display languageFinishing Unplug the power cableZoom ring Adjustment of the Projection ScreenAdjustment of the Projection Screen Adjust the projection image to the screenLowering the projection image Making Adjustments with the AdjustersFocus ring Raising the projection imageAutomatic Adjustment of Analog RGB General OperationInput Selection Freezing a Moving Picture Cancelling Video and Audio TemporarilyAdjustment of the Volume Press the Cancel button to immediately close the displayEnlargement of the Image and Video Movement Image can also be moved in the following circumstancesPress the Zoom button to enlarge the image Using the Presentation Timer Operation Using the Laser PointerClick button Connecting the computer and projectorClick button on back JOG buttonsCN-2 D-Sub 9-pin side Connecting via a LAN U7-137 onlyControlling the Projector from a Computer RS-232C connectionsProtecting the Projector with the Security Lock Changing the password Input the password using the number buttons 1 toCanceling the password/Changing the password Canceling the passwordVolume Using the Quick MenuContent of Adjustments and Settings Press the Select or button to adjustNames and Functions of Buttons Used for Menu Operations Menu Operation MethodMenu Operation Method Menu Screen Names and FunctionsMenu Display Press the Menu button to display the menu Performing Menu OperationsSub menu Making Adjustments/SettingsSelecting Another Menu Name with Remote Control Operation RGB Terminal Menu name Item Name Sub Menu SetupPicture Adj. / Fine Picture / H Position / V Position Picture Adj. Picture AdjustmentImage Brightness / Contrast / Color / Tint / SharpnessImage ResetFine Picture PositionGamma Select the preset color modeColor Quick Color AdjColor Space Selection contents at the time of YPbPr inputColor Temp WhiteWhite Balance Aspect Personal Computer SignalVideo Signals ViewView Vertical Flip / Horizontal FlipKeystone Keystone SaveMenu Position SetupAuto Power Off Auto SourceInput Format Lamp ModeSetup Status IndicatorTo start the timer Presentation TimerBackground OptionLanguage On ScreenOption Network PasswordStartup Screen Security LockStatus Factory DefaultLamp Timer Reset InfoResolution / Frequency Lamp TimerInfo When an Indicator is Lit or Blinking Indicator status What you should doThermal Protector Check the following matters before requesting servicing TroubleshootingDirty Lens CleaningCleaning a Soiled Projector Main Unit Cleaning the Inside of the ProjectorReplacing the Lamp Cartridge Unplug the power cord Remove the lamp cover Replacing the Lamp CartridgeRemove the lamp cartridge Reset the Lamp Timer Mount the new lamp cartridgeMount the lamp cover Mechanical SpecificationsOptical ElectricalDigital Analog SignalResolution Frequency Video Table of Supported FrequenciesCabinet Dimensions 2005
Top Page Image Contents