PLUS Vision U5-232, U5-111 user manual Replacing the Lamp Cartridge

Page 65

Replacing the Lamp Cartridge

•The lamp that is used as a light source in the projector has a limited service life. The rated service life of the lamp is about 2000 hours (when used in normal mode only). This could be shortened depending on conditions of use and other factors.

Note that lamp life will be extended when the projector is often used in Eco mode. (The rated service life of the lamp means the average value of lamp life for lamps that have been manufactured over a long period, and it is derived from test conditions at this company.)

•When the life of the lamp is exceeded, the STATUS indicator lights a steady red and the message [Replace the Lamp Cartridge] is displayed on the screen. When this occurs, it is time to replace the lamp cartridge. Please make the replacement following the procedure below.

•If the projector is used another 100 hours after the lamp’s service life is reached, the power is set to the standby mode and no longer turns on.

•Contact a store that sells the U5-232/U5-132/U5-112/U5-111 for a replacement lamp. Indicate you need a U5-200 re- placement lamp for the U5-232/U5-132/U5-112/U5-111 (order code 28-050).

CAUTION

•Replacement of the lamp cartridge is performed after switching off the power, waiting for the cooling fan to stop, disconnecting the power plug from the power outlet, and then leaving the projector for about 60 minutes before replacement is started. Replacement of the lamp cartridge during operation or immediately after operation stops will cause burns because of the high temperature.

•Do not remove any screws other than those specified.

•Do not touch the lamp with bare hands. Doing so could shorten the life of the lamp.

•If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can be heard and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may cause injury. If this happens, contact your dealer or the store the projector was purchased.

E-64

Image 65

Contents U5-232/U5-132 U5-112/U5-111 Do not look at the laser pointer’s light source PrecautionsThis label is located on the side of the remote control DOC Compliance Notice Important Safety InformationPower Supply InstallationCleaning Lamp ReplacementMajor Features Table of Contents Table of Contents Checking the Supplied Accessories Velcro strap Pocket Cable storage pouch Checking the Supplied AccessoriesStorage case for projector and accessories Zoom ring E-26 Names of the Main Unit PartsExhaust Vents Focus ring E-27 Lens Lens cap Exhaust Vents Lens Lens capNames of the Main Unit Parts Built-in Security SlotPress the lid towards the front Inserting the BatteriesReplacement Method Names of the Remote Control PartsSide View Top View Remote Control RangeProcedure Up to Projecting to the Screen U5-232/U5-132 Screen Size and Projection Distance Placement GuideU5-112 Screen Size and Projection Distance Placement GuideLens surface of the main unit Width U5-111 Screen Size and Projection DistanceConnections with Personal Computer Personal computer RGB signal cable Supplied itemManufacturer Model Key To Output the External Output Signal of a Notebook ComputerConnecting Personal Computers and Video Equipment Video Equipment with Video Connectors Connections with Composite SignalsVideo Equipment with S-VIDEO Connectors Video cable Supplied item Video cable Suppled itemComponent cable Available as an option Order code Connections with Component SignalsGreen Blue Red Cb Cr Pb Pr Green Blue RedAudio cable Supplied item Connections with the Audio JackAudio cable Supplied item Audio conversion cable Red Operating Switch on the projector powerPress the Enter button to set Power Cable Connections and Switching the Power On/OffThis completes the selection of the display language CursorStandby button on main unit Unplug the power cableFinishing Adjustment of the Projection Screen Adjustment of the Projection ScreenAdjust the projection image to the screen Zoom ringFocus ring Making Adjustments with the AdjustersAdjuster button When Auto Source is On Automatic AdjustmentWhen Auto Source is Off General OperationGeneral Operation Video Signals / Component SignalsSelection of Aspect Ratio Freezing a Moving Picture Cancelling Video and Audio TemporarilyLamp Mode Keystone Adjustment of the VolumePress the Cancel button to immediately close the display Press the Zoom button to enlarge the image Enlargement of the Image and Video MovementImage can also be moved in the following circumstances Using the Presentation Timer Operation Using the Laser PointerClick button on back Connecting the computer and projectorJOG buttons Click buttonUse as a High-Brightness Monochrome Projector Controlling the Projector from a ComputerApplicable Projector U5-232 Serial cable D-Sub 9-pin, straight commercially availableProtecting the Projector with the Security Lock Canceling the password/Changing the password Input the password using the number buttons 1 toCanceling the password Changing the passwordVolume Using the Quick MenuContent of Adjustments and Settings Menu button Menu Operation MethodSelect buttons Enter buttonAdjustment Bar Adjustment Bar and Settings ContentsMenu Screen Names and Functions Menu Operation MethodMenu Display Press the Menu button to display the menu Performing Menu OperationsSub menu Making Adjustments/SettingsThis condition al- lows selection of the item name Selecting Another Menu Name with Remote Control Operation View ColorColor B/W Switching Menu name Item Name Sub Menu SetupVideo OptionImage Picture Adj. Picture AdjustmentBrightness / Contrast / Color / Tint / Sharpness Picture Adj. / Fine Picture / H Position / V PositionPress of the Enter button forces the reset ResetFine Picture PositionColor Select the preset color modeQuick Color Adj GammaColor Temp Selection contents at the time of YPbPr inputWhite Color SpaceWhite Balance View Video SignalsAspect FilterVertical Flip Power cable has been unpluggedKeystone Save ViewColor B/W Switching SetupAuto Power Off Auto SourceStatus indicator is green SetupStatus indicator is off Menu PositionTo start the timer Presentation TimerInput Format Video and S-VideoLanguage OptionOn Screen BackgroundOption Startup ScreenSecurity Lock Lamp Timer Reset Factory DefaultInfo StatusInfo Resolution / FrequencyLamp Timer Thermal Protector When an Indicator is Lit or FlashingCheck the following matters before requesting servicing TroubleshootingCleaning a Soiled Projector Main Unit CleaningCleaning the Inside of the Projector Dirty LensReplacing the Lamp Cartridge Remove the lamp cartridge Replacing the Lamp CartridgeMount the lamp cover Reset the Lamp TimerMount the new lamp cartridge Optical SpecificationsElectrical MechanicalModel U5-112/U5-111 SpecificationsU5-112 U5-111Table of Supported Frequency SignalResolution Frequency Video 216 Unit mm inch Cabinet Dimensions252 216 2003