PLUS Vision U5-732 user manual Precautions, DOC Compliance Notice

Page 2

IMPORTANT SAFETY INFORMATION

Precautions

Please read this manual carefully before using your PLUS Data Projector and keep the manual handy for future reference.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PLUS SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

The above cautions are given on the bottom of the product.

WARNING

TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS CAN BE FULLY INSERTED. DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COM- PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALIFIED PLUS SERVICE PERSONNEL.

WARNING

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

RF Interference

WARNING

The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by PLUS Vision in this manual. Failure to comply with this government regulation could void your right to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

DOC Compliance Notice

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

CAUTION

Do not look at the laser pointer’s light source.

Be sure to heed the following. Pointing the laser beam at the eyes could lead to reduced vision or vision impairment.

Never look at the laser pointer’s light source.

Do not point the laser beam at people.

Do not let children use the laser pointer.

This label is located on the side of the remote control.

Hg: Lamp in This Product Contains Mercury. Dispose of Lamp According to Local, State or Federal Law.

E-2

Image 2
Contents U5-732 DOC Compliance Notice PrecautionsThis label is located on the side of the remote control Do not look at the laser pointer’s light sourceCleaning InstallationPower Supply Lamp ReplacementMajor Features Table of Contents Table of Contents USB cable type A, 2 m / 6.6 feet Checking the Supplied AccessoriesPower cable 1.8 m / 5.9 feet Velcro strap Pocket Cable storage pouch Checking the Supplied AccessoriesStorage case for projector and accessories Names of the Main Unit Parts Zoom ring E-26Built-in Security Slot Names of the Main Unit PartsNames of Parts/Preparing the Remote Control Unit Names of the Remote Control PartsInserting the Batteries Side View Remote Control RangeRemote control sensor 5m/16.4feet 6m/19.7feetProcedure Up to Projecting to the Screen Placement Guide Screen Size and Projection DistancePlacement Guide Lens center Personal computer RGB signal cable Supplied item Connections with Personal ComputerManufacturer Model Key To Output the External Output Signal of a Notebook ComputerConnecting Personal Computers and Video Equipment Video Equipment with S-VIDEO Connectors Connections with Composite SignalsVideo Equipment with Video Connectors → Video See Input Format on Page E-56Green Blue Red Cb Cr Connections with Component SignalsComponent cable Available as an option Order code Pb Pr Green Blue RedAudio cable Supplied item Connections with the Audio JackAudio cable Supplied item Audio conversion adapter Red Switch on the projector power OperatingThis completes the selection of the display language Power Cable Connections and Switching the Power On/OffPress the Enter button to set CursorStandby button on main unit Unplug the power cableFinishing Adjust the projection image to the screen Adjustment of the Projection ScreenAdjustment of the Projection Screen Zoom ringFocus ring Making Adjustments with the AdjustersAdjuster button Raising the projection imageGeneral Operation When Auto Source is OnWhen Auto Source is Off Input SelectionGeneral Operation Automatic AdjustmentPress of the Auto button starts the automatic adjustment Cancelling Video and Audio Temporarily Freezing a Moving PictureAdjustment of the Volume Press the Zoom button to enlarge the image Enlargement of the Image and Video MovementImage can also be moved in the following circumstances Using the Presentation Timer Using the Laser Pointer OperationJOG buttons Connecting the computer and projectorClick button on back Click buttonControlling the Projector from a Computer Serial cable D-Sub 9-pin, straight commercially availableProtecting the Projector with the Security Lock Canceling the password Input the password using the number buttons 1 toCanceling the password/Changing the password Changing the passwordVolume Using the Quick MenuContent of Adjustments and Settings Select buttons Menu Operation MethodMenu button Enter buttonMenu Screen Names and Functions Adjustment Bar and Settings ContentsAdjustment Bar Menu Operation MethodPerforming Menu Operations Menu Display Press the Menu button to display the menuSub menu Making Adjustments/SettingsThis condition al- lows selection of the item name Selecting Another Menu Name with Remote Control Operation Color ViewOption Menu name Item Name Sub Menu SetupVideo InfoBrightness / Contrast / Color / Tint / Sharpness Picture Adj. Picture AdjustmentImage Picture Adj. / Fine Picture / H Position / V PositionFine Picture ResetPress of the Enter button forces the reset PositionQuick Color Adj Select the preset color modeColor GammaWhite Selection contents at the time of YPbPr inputColor Temp Color SpaceWhite Balance View Personal Computer SignalVideo Signals AspectKeystone Save Vertical Flip / Horizontal FlipKeystone ViewAuto Source SetupAuto Power Off Status Indicator Lamp ModeSetup Menu PositionInput Format Presentation TimerTo start the timer Video and S-VideoOn Screen OptionLanguage BackgroundOption Startup ScreenSecurity Lock Info Factory DefaultLamp Timer Reset StatusInfo Resolution / FrequencyLamp Timer When an Indicator is Lit or Flashing Thermal ProtectorTroubleshooting Check the following matters before requesting servicingCleaning the Inside of the Projector CleaningCleaning a Soiled Projector Main Unit Dirty LensReplacing the Lamp Cartridge Replacing the Lamp Cartridge Remove the lamp cartridgeMount the lamp cover Reset the Lamp TimerMount the new lamp cartridge Electrical SpecificationsOptical MechanicalTable of Supported Frequency SignalResolution Frequency Video On Apple MacintoshCabinet Dimensions 260 216 Unit mm inch2005