Planar M70L manual Using the Remote, If the Remote Doesn’t Work

Page 32

Using the Remote

Using the Remote

The remote control operates with IR (infrared) signals going to the IR receiver (located in the lower right corner of the screen for landscape and in the lower left corner for portrait).

(Later, to prevent accidental adjustment of the display, you can disable the remote control function using an RS232 command.)

Note: The remote control has a large spread of its IR radiation. It is difficult from a distance to control only one display in an array; step closer.

If the Remote Doesn’t Work

•The batteries in the remote are dead or installed wrong.

•The remote was not aimed at the screen.

•Something is blocking the IR receiver in the display.

•IR remote action was disabled by an RS232 command.

24	m70L Installation & Configuration Guide

Image 32

Contents M70L Installation & Configuration Guide Page Disclaimer Warranty and Service Plans RoHS Compliance StatementTrademark Credits M70L Installation & Configuration Guide Table of Contents DVD and Component Video Sources Composite Video and S-Video Retry on Lost Signal Downloading Additional Documentation and Firmware Introduction Safety for You and the m70L General Safety PrecautionsPage InformationDisposal 7KH WLOOGXU What is Temporary Image Retention? Recommended UsageBurn-In Versus Temporary Image Retention Static Image ApplicationsNormal Use Thermal Guidelines Vesa Mounts, General Description Installing an m70L Plan Your InstallationPrepare Your Installation Location Before You BeginBefore You Begin Accessories With Each m70L Display Installation ChecklistUnpacking and Checking Accessories Optional Accessories Customer-Supplied AccessoriesInstalling the Video Input Module VIM Connector Installing the Video Input Module VIM Installing the Video Input Module VIM Connecting Source Cables Connecting Picture SourcesInput Found on the Following Devices Using the DVI Out ConnectorSelecting the Correct Input Connecting Power About UPS SuppliesConnecting Power Wiring the adapter RS232 CommunicationConnecting RS232 Cables Configuring an m70L Using the Remote If the Remote Doesn’t WorkSource Connectors Selecting the SourceType Resolution Computer SourcesComponent Video Sources DVD and Component Video SourcesAutomatically Selecting the Source Manually Selecting the SourceSource popup menu displays to the right of the Picture menu Analog SDI Adjusting Input Levels Adjusting Levels for Analog SourcesWhy Adjust Levels? Semi-Automatic Level AdjustmentTo access the Input Levels menu, press Level on the remote Manual Level Adjustment Adjusting Levels for Digital Sources Adjusting Levels for Video Sources Adjusting the Picture With Color BarsAdjusting Input Levels Adjusting Frequency and Phase Making a Checkerboard Pattern With PaintAdjusting Frequency Manually Adjusting Phase ManuallyAspect Ratio Settings Scale Mode SettingsMode VGA/SVGA/XGAAspect Ratio Settings Justify Settings Wall ModeOverscan Wall Width and Wall HeightAdjusting Sharpness Sharpness SettingsAdjusting Sharpness Adjusting Position Picture PositionHorizontal Position Vertical PositionAdjusting Position Viewport Display ResolutionViewport Viewport Adjusting Color Balance Understanding Color TemperatureAdjusting Color Temperature Color Balancing a Single DisplayTips for Color Balancing Color BalanceBrightness Adjusting Color Balance Advanced Options Advanced OptionsPlug and Play Edid Enable Miscellaneous OptionsCurtain Pattern Preferred Source DetectionAuto Setup Options Retry on Lost SignalDo Frequency and Do Phase Do CheckboxesMenu Timeout Menu OptionsPosition Rotate MenuRecall Last MIP TimeoutMessage in Picture Setting the Clock/Scheduling an Event EventsSet Clock / Schedule Events Setting the Clock Scheduling an EventAdvanced Options New events on the SET Clock / Schedule Events menu Backlight Settings Backlight ControlManual Backlight Control Auto Backlight ControlAuto Backlight On High Temperature WarningTurn Backlight Off With No Source and Dpms Delay Backlight Control Group ID and Unit ID Serial Port Settings and DiagnosticsSerial Port Settings Ascii Response Type Ascii Response TerminatorGroup ID Unit ID Address Affect on DisplaysBaud Rate Controlling With RS232 CommandsSerial Port Status Serial Port Settings and Diagnostics How Automatic Save Works Saving and Recalling ConfigurationsAdvantages of Saving Configurations to Memory Slots Global Storage Memory What Is Saved? And Where?What the Memories Store Color Balance all values Saving Configurations RGBChanging the Name of the Memory Slot Saving and Recalling Configurations Recalling Stored Configurations Deleting a Configuration Press Enter Saving and Recalling Configurations Basic Troubleshooting Do This Result Explanation / Further ActionPossible Resolution Internal Temperature Possible Cause Possible ResolutionChecking Unit Status Backlight Status ShowsWhere to Go From Here Accessing Planar’s Technical Support Website Downloading Utility Software Document Name ContentsDownloading Additional Documentation and Firmware Specifications Mechanical SpecificationsInput connectors TTL H and V syncElectrical and Heat Specifications Max Min Typical Unit AC RequirementsHeat, BTUs per hour Analog InputsSDI Input Composite InputVideo Input Optical Specifications Maximum Minimum Environmental Specifications Maximum Minimum TypicalMounting Specifications Screw SizeM70L Installation & Configuration Guide M70L Dimensions Front and Side ViewRear View Regulatory Information M70L Installation & Configuration Guide Index Operation NumbersAdvanced options, 53 aspect ratio, 39 aspect ratio & wall PAL, 26 parameters Index