InFocus LP1200 appendix Replacement of a light source lamp

Page 40

Replacement of a light source lamp

ENGLISH

The light source lamp is designed to project the image on the LCD panel. When the light source lamp no longer functions, replace it with a new one to ensure optimum performance.

Caution:

• Do not remove the light source lamp from inside of

this equipment immediately after using the projec-

tor, you may get burned because of the high tem-

perature of the light source lamp.

3.Set Lamp exchanging metal into the projector.

1)Insert metal fittings for lamp replacement in the following positions: on the front face of the lamp (2 positions), between the lamp, and on the bottom edges (4 positions).

2)Align screw holes (c) with node (d).

3)Fasten the piece into place using the two screws included (b, b’).

(d)

• When you replace the light source lamp, press the

power button to power off, then wait for 120 sec-

onds in stand-by mode to cool down the lamp and

LCD panels. Turn off the main switch, unplug the

power code from the outlet and wait one hour so

that the lamp is cool to the touch.

(c)

(e)

(b)

(b')

Lamp exchange metal

• Do not remove the light source lamp except for re-

placement. Careless treatment can cause injury or

fire.

• Do not touch the lamp directly. It may be broken

and may cause you to injure or burn yourself.

• Be sure not to drop the lamp lid screw into the pro-

jector. Also be sure also not to insert metal or any

flammable objects, it may cause fire or an electric

shock. If any objects are inserted, please unplug and

contact your dealer.

• Install the lamp securely, failure to do so it may

cause a fire.

1. Loosen the screw of

Loosen here

the lamp lid on the

 

top cover using a

 

screwdriver (+) , and

 

remove the lid.

 

Remove the lamp cover in the direc-

tion of the arrow as indicated.

Important:

Be careful not to damage the electric wire connected to this equipment.

 

Hooks

Lamp

(x 6)

4.Loosen the lamp fixing screw (e) using a screwdriver (+), and remove it.

5.Hold onto the projector

by the handle as you pull

Handle

out the lamp.

 

For the lamp you have

 

removed, do not spill liq-

 

uid on it, place it near

 

flammable objects or

 

where children can touch

 

it. Otherwise, it will cause in-

 

jury or fire.

 

6.Insert the new lamp securely into the projector body in the right direction.

7.Tight up the screws (e) which

have been removed in 4 using a screwdriver (+).

2. Loosen a screw (a) of fix-

(a)

Fixing

ing metal using a screw-

 

metal

driver (+), and remove

 

 

them.

 

(e)

Do not lose the fixing

 

metal and screws.

 

 

8.Loosen the two screws (f), (f') of lamp exchanging metal us- ing a screwdriver, and remove them with the metal.

9.Remove the holes from the lamp replacement metal fittings (c) from the node (d).

(f)(f')

(e)

10. Insert the fixed metal pieces

 

from step 2 into the screw

(a)

holes (f) and (f’), and use one

 

screw (a) to hold the piece in

 

place.

 

40

Image 40
Contents E R ’ S G U I D E When using the projector in Europe Compliance NoticeContents Important safeguards Never remove the cabinet Do not modify this equipmentIf you break or drop the cabinet Do not face a lens to the sunOverview of the projector FINE, º, ª, FOCUS/ZOOM and Auto Position buttonsPower jack RS-232 2 input Mini DIN 8P PC card ejectPC card insert slot PC audio input stereo mini jackOverview of the remote control RGB, VIDEO, CardBattery installation Operation areaPreparing the projector for operation Orientation of the projectorFront projection Front projection, ceiling mountAdjusting the angle of projection Getting ready for projectionBasic connections Projector + AV equipmentCables and adapters Projector + DVD playerProjector + IBM PC or IBM PC compatibles Desktop computerPower Book When outputting to both a PC monitor and the projectorBasic connections continue Projector + MacintoshDesktop computer display connector Projector + NEC PC-98 seriesTo operate projector power on Lamp PowerLeft side ButtonTurning off the projector Volume from the speakerAuto Position button Menu operation Basic operationPicture BrightnessSignal PictureInstallation PinP/EXPANDPC Card Auto Play AudioOption VerPicture adjustment Adjustment from personal computerCGA70 Gamma Correction menu MasterAdvanced feature for presentation Cursor operationStill FastslowSetting the Expand mode Using the Expand modeIndication Mode 4 actual size display Super impose Picture in PictureUsing the PC-CARD Setting up the PC-CARDRelease the PC-CARD Play backPC-CARD Continue Card Auto PlayAdvanced feature with PC Installation of softwareEnvironment PCV PC Card ViewerCommand reference For Windows 95 or Windows NT Starting up PCV For WindowsRecording the image For Windows Editing the presentation For Windows Command reference Starting up PCV For MacintoshRecording the image For Macintosh JpegEditing the presentation For Macintosh Pcgc Personal Computer Graphic Control ConnectionStarting up Pcgc SpacePointer Setting of SpacePointer Operation of PC by remote controlFor Windows Uninstallation of software Replacement of a light source lamp How to reset the operation time meter Life of the lampMaintenance Cleaning the air-filterCleaning the projector and the ventilation slots Cleaning the lensTroubleshooting CauseIndicators Indicator Shows Condition Possible SolutionsIndicator TempReplacement parts list SpecificationsWhat’s included in the box Warranty Limitation and Exclusion Limited warrantyDisclaimer of Unstated Warranties Appendix Control this projector by using a personal computer InterfaceOperation commands Control this projector by using a personal computer Continue Reading command diagram 871D219B9