Marantz PD5050D manual Declaration of Conformity

Page 36

*1 Only when using a graphic accelerator board that is capable of displaying 852480.

*2 PD4230V : Display only 400 lines with the screen center of the vertical orientation located at the center. PD4250D : Display only 640 lines with the screen center of the vertical orientation located at the center. PD5050D : This signal is converted to a 1024 dots  640 lines signal.

*3 The picture is displayed in the original resolution. The picture will be compressed for other signals (PD4230V/PD4250D). *4 PD4230V : Aspect ratio is 5:4. This signal is converted to a 600 dots480 lines signal.

PD4250D : Aspect ratio is 5:4. This signal is converted to a 720 dots768 lines signal.

PD5050D : The aspect ratio is 5:4. This signal is converted to a 960 dots768 lines signal.

*5 Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the RGB mode prepared for the input signals listed in the table above.

*6 To connect the monitor to Macintosh computer, use the monitor adapter (D-Sub 15-pin) to your computer's video port.

*7 Other screen modes (ZOOM and STADIUM) are available as well.

*8 When viewing a moving picture at a vertical frequency greater than 65Hz, the picture may sometimes be unstable (jumpy). If this occurs, please set the refresh rate of the external equipment to 60Hz.

To view 480I@60Hz (480 interlaced lines, 60Hz refresh rate) or 576I@50Hz (567 interlaced lines, 50Hz refresh rate) when sync polarity is “Sync on Green”, set “RGB SELECT” to “MOTION”.

*9 CVT standard compliant.

NOTE:

•While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size of the picture or the fine picture because of errors in synchronization of your computer.

•When a 1280 dots  1024 lines signal or 1600 dots  1200 lines signal is input to the monitor, the picture will be compressed (PD5050D).

•PD4230V : This monitor has a resolution of 853 dots480 lines. It is recommended that the input signal should be VGA, wide VGA, or equivalent.

PD4250D : This monitor has a resolution of 1024 dots768 lines. It is recommended that the input signal should be XGA, wide XGA, or equivalent.

PD5050D : This monitor has a resolution of 1365 dots  768 lines. It is recommended that the input signal should be XGA, wide XGA, or equivalent.

•With digital input some signals are not accepted.

•The sync may be disturbed when a nonstandard signal other than the aforementioned is input.

•If you are connecting a composite sync signal, use the HD terminal.

•“IBM PC/AT” and “VGA” are registered trademarks of International Business Machines, Inc. of the United States.

•“Apple Macintosh” is a registered trademark of Apple Computer, Inc. of the United States.

•HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDM2 licensing LLC.

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

U.S. Responsible Party:

Marantz America, Inc.

 

Address:

1100 Maplewood Drive,

 

 

Itasca, IL 60143, U.S.A.

 

Tel. No.:

630-741-0300

 

 

 

 

Type of Product:

Plasma Display

Equipment Classification:

Class B Peripheral

Models:

PD4230V/UIB, PD4250D/UIB, PD5050D/UIB, PD6150D/UIB

We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules.

40

Page 35 Page 37
Image 36
Page 35 Page 37
Contents
Model PD5050D User Guide Important Safety Instructions Avertissment What is covered? What is excluded?Before requesting service To get warranty serviceImportant Information Recommandations importantes AvertissementDOC avis de conformation Precautions Plasma monitor cleaning procedureTo avoid damage and prolong operating life Recommendations to avoid or minimize phosphor burn-inPrécautions Mises en garde et précautions de sécuritéMéthode de nettoyage du moniteur à plasma Contents Installation Ventilation Requirements for enclosure mountingHow to use the remote control Battery Installation and ReplacementHandling the remote control Cable ManagementTurns the monitor’s power on and off Receives the signals from the remote controlPart Names and Function Front ViewRear View/ Terminal Board Remote Control Basic Operations When viewing videos or digital video discs Wide OperationsWide Screen Operation with Computer Signals When wide signals are input Supported resolution Normal size screen 43 or SxgaOSM On Screen Menu Controls Menu OperationsMenu Tree Main menu Sub menu Sub menu 3 Sub menuOnly when Auto Picture is OFF RGB/PC only  Restoring the factory default settingsPicture Settings Menu Storing picture settingsAdjusting the picture Reducing noise in the pictureSetting the color temperature Adjusting the color to the desired levelMaking the Low Tone adjustments Changing the Gamma CurveAdjusting the pedestal level black level Adjusting the colorsSetting the picture to suit the movie Audio Settings Menu Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture ADJSET UP Settings Menu Setting the signal and black level for Hdmi signal Setting the video signal formatSetting the background color when no signal is being input Setting the screen size for S1/S2 video input Setting the position of the menuResetting to the default values Turning on/off the menu displayFunction Settings Menu Setting the power management for computer imagesPOWER/STANDBY indicator Setting the Input SkipPeak Bright settings Orbiter settingsINVERSE/WHITE Settings Soft Focus settingsSignal Information Menu Setting Closed CaptionReducing the brightness of Closed Caption External Control Pin AssignmentsTroubleshooting Symptom Checks RemedySpecifications PD5050D SignalsTable of Signals Supported  PD5050D Supported resolutionComputer input signals supported by this system Declaration of Conformity Is a registered trademark