Marantz PD6001 manual CVT standard compliant, KHz 169

Page 39

 

Model

Dots × lines

Vertical

Horizontal

Sync Polarity

Presence

Screen mode

RGB 4

 

 

 

frequency

frequency

Horizontal

Vertical

Horizontal

Vertical

NORMAL

ANAMORPHIC

Memory

 

 

 

 

select*

 

 

Signal Type

 

(Hz)

(kHz)

 

 

 

 

(4:3)

(16:9)

 

 

 

Work Station

1280×1024

60.0

64.6

NEG

NEG

YES

YES

YES*3

YES

1280×1024

29

 

(EWS4800)

 

71.2

75.1

NEG

NEG

YES

YES

YES*3

YES

– –

48

 

Work Station (HP)

1280×1024

72.0

78.1

– –

– –

– –

– –

YES*3

YES

– –

59

 

Work Station

1152×900

66.0

61.8

C Sync

C Sync

– –

– –

YES

YES

– –

60

 

(SUN)

 

76.0

71.7

C Sync

C Sync

– –

– –

YES

YES

– –

61

 

 

 

1280×1024

76.1

81.1

C Sync

C Sync

– –

– –

YES*3

YES

– –

30

 

Work Station

1024×768

60.0

49.7

– –

– –

– –

– –

YES*2

YES

1024×768

62

 

(SGI)

1280×1024

60.0

63.9

– –

– –

– –

– –

YES*3

YES

1280×1024

29

 

IDC-3000G

 

 

 

 

 

 

 

 

 

 

 

 

 

PAL625P

768×576

50.0

31.4

NEG

NEG

YES

YES

YES*6

YES*6

– –

31

 

 

NTSC525P

640×480

59.9

31.5

NEG

NEG

YES

YES

YES*6

YES*6

525P

32

 

*1

Only when using a graphic accelerator board that is capable of displaying 852×480.

 

 

 

 

 

*2

The picture is displayed in the original resolution.

 

 

 

 

 

 

 

 

*3

The aspect ratio is 5:4. This signal is converted to a 960 dots×768 lines signal.

 

 

 

 

 

*4

Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the

 

RGB mode prepared for the input signals listed in the table above.

 

 

 

 

 

 

 

*5

To connect the monitor to Macintosh computer, use the monitor adapter (D-Sub 15-pin) to your computer's video port.

*6

Other screen modes (ZOOM and STADIUM) are available as well.

 

 

 

 

 

 

 

*7

CVT standard compliant.

 

 

 

 

 

 

 

 

 

 

NOTE:

•While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size of the picture or the fine picture because of errors in synchronization of your computer.

•When a 1280 dots×1024 lines signal or 1600 dots×1200 lines signal is input to the monitor, the picture will be compressed.

•This monitor has a resolution of 1365 dots×768 lines. It is recommended that the input signal should be XGA, wide XGA, or equivalent.

•With digital input some signals are not accepted.

•The sync may be disturbed when a nonstandard signal other than the aforementioned is input.

•If you are connecting a composite sync signal, use the HD terminal.

•“IBM PC/AT” and “XGA” are registered trademarks of International Business Machines, Inc. of the United States.

•“Apple Macintosh” is a registered trademark of Apple Computer, Inc. of the United States.

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

U.S. Responsible Party:

Marantz America, Inc.

Address:

100 Corporate Drive,

Tel. No.:

Mahwah, NJ, 07430, U.S.A.

630-741-0300

 

 

Type of Product:

Plasma Monitor

Equipment Classification:

Class B Peripheral

Models:

PD6001

We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules.

46

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Model PD6001 User Guide Additional Safety Information Important Safety InstructionsInformations de Sécurité Supplémentaires AvertissmentImportant Information PrecautionsRecommandations importantes PrécautionAvertissements et précautions de sécurité Operating Environment PD6001 Remarque AvertissementContents Ventilation Requirements for enclosure mounting InstallationOperating Range Using the remote controlBattery Installation and Replacement Cable ManagementFront View Turns the monitor’s power on and offReceives the signals from the remote control Part Names and FunctionPD6001 Rear View/ Terminal BoardRemote Control Basic Operations Wide Operations When viewing videos or digital video discsNormal size screen 43 or Sxga Wide Screen Operation with Computer SignalsWhen wide signals are input  Supported resolutionOperations in the Side-by-side mode Split Screen OperationsShowing a couple of pictures on the screen at the same time Zooming in on a specific input Operations in the Picture-in-picture modeSelecting the input signals to be displayed Adjusting the OSM controlsMenu Operations  Advanced menu modeMain menu Sub menu Sub menu 3 Sub menu Menu TreeReset  Restoring the factory default settingsReducing noise in the picture Picture Settings MenuStoring picture settings Adjusting the picture Adjusting the white balance Setting the color temperatureAdjusting the color to the desired level Setting the picture to suit the movieChanging the Gamma Curve Making the Low Tone adjustmentsAdjusting the pedestal level black level Adjusting the colorsAudio Settings Menu Image Adjust Settings MenuSetting the allocation of the audio and DVD/ HD connectors SET UP Settings Menu Setting the black level for Hdmi signal Setting the video signal formatSetting the background color when no signal is being input Setting the position of the menu Etting the screen size for S1/S2 video inputTurning on/off the menu display Setting the power management for computer images Function Settings MenuResetting to the default values Setting the menu modeDisplaying still images in the sub screen ON/STANDBY indicatorSetting the Input Skip Displaying the entire image during Digital Zoom operationsReducing image retention  When set to Auto Peak Bright settings  Orbiter settings OSM Orbiter settings Setting Closed Caption INVERSE/WHITE Settings  Soft Focus settingsSignal Information Menu Setting the power on modeReducing the brightness of Closed Caption Pin Assignments External Control1/8 Stereo Mini cable must be purchased separately Connection Example Connecting an STBConnection with STB Connection ExampleSymptom Checks Remedy TroubleshootingSpecifications PD6001 Computer input signals supported by this system Supported resolution PD6001KHz 169 CVT standard compliantIs a registered trademark
Top Page Image Contents