ENGLISH | GOLDEN SCAN 3 HMI 1200 TV |
| HMI 575 |
| HMI 1200 |
Congratulations on choosing a Clay Paky product! We thank you for your custom. Please note that this product, as all the others in the rich Clay Paky range, has been designed and made with total quality to ensure excellent performance and best meet your expectations and requirements.
INSTRUCTIONS MANUAL
Carefully read this instructions manual in its entirety and keep it safe for future reference.
It is essential to know the information and comply with the instructions given in this manual in order to ensure the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to other property or persons deriving from installation, use and maintenance that have not been carried out in conformity with this instructions manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the characteristics stated in this instructions manual at any time and without prior notice.
1 | SAFETY INFORMATION |
• Installation
Make sure all the parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector.
The safety rope, properly hooked onto the fitting and secured to the framework, must be installed so that, if the primary support system fails, the fitting falls as little as possible. If the safety rope gets used, it needs to be replaced with a genuine spare.
• IP20 protection rating
The fitting is protected against penetration by solid bodies of over 12mm (0.5”) in diameter (first digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0).
• Protection against electrical shock
This fitting is classified in accordance with the type of protection against electrical shock, in Class I. It must therefore be connected to a power supply system with efficient earthing.
It is however recommended to protect the supply lines of the projectors from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
• Connecting to the supply mains
Connection to the electricity mains must be carried out by a qualified electrical installer.
Check that the mains frequency and voltage correspond to the frequency and voltage stated on the electrical data label for which the projector is designed.
This label also gives the input power. Refer to this to evaluate the maximum number of fittings to connect to the electricity supply in order to avoid overloading.
• Maintenance
Before starting any maintenance work or cleaning the projector, cut off power from the mains supply.
After switching off, do not remove any parts of the fitting for 10 minutes.
After this time the likelihood of the lamp exploding is virtually null. If it is necessary to replace the lamp, wait for another 15 minutes to avoid getting burnt.
The fitting is designed to hold in any splinters produced by a lamp exploding. The lenses must be fitted and, if visibly damaged, they have to be replaced with genuine spares.
ENGLISH
• Minimum distance from target objects
The projector must be positioned in such a way that objects struck by the beam are separated from the lens at least by the distance indicated on the lamp change label against the symbol shown alongside.
• Minimum distance of flammable materials
(8’ 2’’) 2.5 m
(5’ 11’’) 1.8 m 
HMI 1200
HMI 575
• Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is 90°C (194°F).
• Lamp
The projector must be positioned so that any flammable materials are at least 0,1 meter (4”) for HMI 1200 and 0,07 meter (3”) for HMI 575 from every point on the surface of the fitting.
It is permissible to mount the fitting on normally flammable surfaces.
• Maximum ambient temperature
For the fitting to operate well and reliably, the ambient temperature should not exceed 35°C (95°F).
The projector mounts a
-Carefully read the "operating instructions" provided by the lamp manufacturer.
-Immediately replace the lamp if damaged or deformed by heat.
The products referred to in this manual conform to the
European Community Directives to which they are subject:
•Low Voltage 73/23
•Electromagnetic Compatibility 89/336
1