JVC TM-H1950CG Also used as a control button in the menu function mode, Screen, Unlit

TM-H1950CG

CONTROLS AND FEATURES

FRONT VIEW

<Front Panel>

1

CHROMA	CONTRAST	VOLUME/SELECT
15
PHASE	BRIGHT

MENU	UNDER	COLOR	BLUE	ASPECT	A	B	C	SLOT	D	POWER
	SCAN	OFF	CHECK
						INPUT	SELECT

2

3

4

5

6

7

8

9 10

11

12

134

(Front view of TM-H1950CG shown)

1 Tally lamp

Lights when the tally control signal is ON. The tally control signal is input through the REMOTE (external control) remote terminal. For details, refer to Page 18.

2	Chroma/Phase button
	[ CHROMA/	PHASE]
	Press this button to activate the picture color density
	adjustment mode or picture hue adjustment mode. Each
	time you press the button, the adjustment item changes.
	Picture color density		f Picture hue
	Adjust the value with the VOLUME/SELECT buttons			4.

Also used as a control button in the menu function mode.

8 Blue Check button [BLUE CHECK] Cuts red and green signal components. Only blue signal components are shown. Press the button again to restore the normal image.

When selected, this button lights.

9 Aspect button [ASPECT]

Press this button to change the aspect ratio from 4:3 to 16:9.

10 Input A (VIDEO) button [INPUT SELECT A]

Selects the video and audio signals input to the VIDEO A

*and AUDIO A q terminals on the rear panel. The button lights when selected.

3	Contrast/Brightness button
	[CONTRAST	/ BRIGHT	]
	Press this button to activate the picture contrast adjustment
	mode or picture brightness adjustment mode. Each time
	you press the button, the adjustment item changes.
	Picture contrast f Picture brightness
	Adjust the value with the VOLUME/SELECT buttons		4.
	Also used as a control button in the menu function mode.
	Volume/Select buttons
4
	[VOLUME/SELECT –	+]

Adjusts the speaker volume. Also used as a control button in the menu function mode.

5 Menu button [MENU]

Displays and disappears the <MENU> screen.

Pressing the CHROMA/PHASE button2 with the Menu button depressed will display the <SET-UP MENU>

screen.

6 Under Scan button [UNDER SCAN]

Reduces the screen size to display the entire image.

Press the button again to cancel Under Scan.

When selected, the Under Scan button lights.

7 Color Off button [COLOR OFF]

Cuts color signals to display a black and white image.

Press the button again to restore the original color.

When selected, the COLOR OFF button lights.

Note:

●This function is invalid with RGB input.

11 Input B (VIDEO Y/C) button [INPUT SELECT B]

Selects the video and audio signals input to the VIDEO B

( or VIDEO B (Y/C) ) and AUDIO B w terminals on the rear panel. The button lights when selected.

Note:

●The VIDEO B terminals include a video terminal (BNC connector) and a Y/C terminal (mini-DIN 4-pin connector). The Y/C (S-video) terminal has priority.

12 Input C/D (Slot) buttons [INPUT SELECT C/D (SLOT)]

Selects the signals to be input via the input cards installed in the rear panel card slots.

C, D : Selects the image from the input card in the slot.

		For details on input connectors and using the INPUT
		SELECT button, refer to page 7.
	Power indicator
13
	Unlit	: The main power is OFF.
	Orange : The main power is ON, but the monitor’s power
		is OFF (in the stand-by mode).
	Green	: The main power is ON, and the monitor’s power
		is ON (in the normal operation mode).
	Power switch [POWER
14			]

Press the power switch to turn the monitor’s power ON or

OFF when the main power is ON.

Note:

●When RUSH DELAY is set to SLOW, it takes about three seconds before power is actually supplied after the power switch is pressed.

15 Speaker

A built-in speaker is located inside the right side panel when the monitor is viewed from the front.

4

1-4 No.51961