JVC TM-H1900G Video Signal Controls, Display and Selection in the Menu Screen Mode Setting

4): Indicates the

HOW TO HANDLE BASIC OPERATIONS (cont’d)

VIDEO SIGNAL CONTROLS

HOW TO USE THE MENU FUNCTIONS

DISPLAY AND SELECTION IN THE <MENU> SCREEN MODE (SETTING)

Use these buttons for video signal control.

UNDER SCAN

Press the UNDER SCAN button to reduce the size of display area

so that the whole picture is displayed on screen. Use to check the picture frame.

You can set the following menu items.

Set them depending on your needs.

• SHARPNESS	• COLOR SYSTEM
• ADJ. BAR POSI.	• RUSH DELAY
• COLOR TEMP.	• ASPECT RATIO

1. Press the MENU button.

MENU	The <MENU> screen is displayed.
	* The on-screen display goes off automatically after about five
	minutes with operation performed.

<MENU> screen

1< MENU >

	4	SHARPNESS		: 00
		ADJ. BAR POSI.		:		LOWER
		COLOR TEMP.		: 6500
		COLOR SYSTEM		: AUTO
		RUSH DELAY		: STD.
2		ASPECT RATIO		: 4-	3		3
			EXIT			4

2.Press the CHROMA/PHASE or CONTRAST/BRIGHT button to select MENU items.

CHROMA	CONTRAST	VOLUME/SELECT	MENU
PHASE	BRIGHT

No.51960

CHROMA	CONTRAST
PHASE	BRIGHT
	SHARPNESS
	ADJ. BAR POSI.
	COLOR TEMP.
	COLOR SYSTEM
	RUSH DELAY

A selection mark (	4) is put next to the selected item.
Front panel	Function	Contents
button	displayed
CHROMA/		Forward selection mark (	4)
PHASE
CONTRAST/		Reverse selection mark (	4)
BRIGHT

<Front panel buttons>

1 Selection mark ( menu item you select.

2Menu item: Menu items you can

select.

3Setting display: Indicates the current settings (value).

4Function display: The functions of the front panel buttons (5 buttons on the left) correspond to the function displayed.

ENGLISH

1-5 8

ASPECT RATIO

3. Press the VOLUME/SELECT buttons to set.

VOLUME/SELECT	Front panel	Function	Contents
	button	displayed
	VOLUME/	+	Increase (to max. value)
	SELECT (+)	4	Forward the setting value
	VOLUME/	–	Decrease (to min. value)
	SELECT (–)	1	Reverse the setting value

Menu items		Purpose						Setting range
SHARPNESS	Picture	sharpness	00	+01				• • • • • • • • •+39• • • +4
ADJ.BAR POSI	Volume bar position		LOWER				UPPER
COLOR TEMP.	Color temperature of white		6500				9300
		balance
COLOR SYSTEM	Color system		AUTO		NTSC			AUTO	PAL
RUSH DELAY	Delay value		STD.			SLOW
ASPECT RATIO	Aspect ratio		4 - 3		16 - 9

*For normal use, leave the COLOR SYSTEM setting to AUTO.

If reception is unsatisfactory in AUTO position, set it to the appropriate color system mode (NTSC or PAL).

*When REMOTE SYSTEM is set to MAKE, and REMOTE ENABLE signal is short circuited (ON), “REMOTE” is displayed on the ASPECT RATIO setting menu, and Aspect ratio cannot be operated from the front panel.

4.If you want to set the other menu items, repeat procedures 2 and 3.

5.Press the MENU button to quit.

MENU	Front panel	Function		Contents
	button		displayed
	MENU		EXIT	Quit (or Release) the <MENU>
				screen

Function	Contents
displayed
	Forward the menu item.
	Reverse the menu item.
–	Lower the adjustment
	value. (to the minimum)
+	Raise the adjustment
	value. (to the maximum)
4	Forward the setting value.
1	Reverse the setting value.
EXIT	Exits the <MENU> screen.

Notes:

●When the screen aspect ratio is set to

16 - 9 (16:9) in ASPECT RATIO, the picture will be vertically reduced.

●RUSH DELAY sets the delay between the time the power switch is pressed and the time power is actually supplied to the monitor’s circuits.

STD. : Power turns on approxi- mately 1 second after the power switch is pressed.

SLOW : Power turns on approxi- mately 3 seconds after the power switch is pressed.

*When turning on multiple Color- Video Monitors simultaneously, it is recommended to use STD. or

SLOW settings to reduce the rush current of the entire system.

9

TM-H1900G