JVC V1700CG manual Function Setting, Picture SUB ADJ

HOW TO USE “SETUP MENU” (cont'd)

ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS

1.FUNCTION SETTING

Selects the colour system and displays the monitor’s power-

up time or the total usage time. Press the button to display the setting menu illustrated on the right.

<FUNCTION SETTING>

COLOR SYSTEM		:AUTO
RUSH DELAY	TIME	:STD.
HOUR METER	X100h	:000

EXIT: MENU ADJUST:-+ SELECT:

Item	: CONTRAST
Adjustment
range	: –20 ~ 00 ~ +20
Function	: For approximate adjustment of the picture
		contrast. Before adjustment, set the CONTRAST
		knob on the front panel to 0.
Item	: BRIGHT
Adjustment
range	: –20 ~ 00 ~ +20
Function	: For approximate adjustment of the picture

Item	: COLOR SYSTEM
Settings	: AUTO/NTSC/PAL
Function	: Selects the colour system when using the video
	input card.
	AUTO : Change NTSC and PAL automatically.
	NTSC : Keeps the colour system NTSC.
	PAL : Keeps the colour system PAL.

NOTE : Normally select AUTO. However, if the input signal is unstable, select NTSC or PAL.

Item	: RUSH DELAY TIME
Settings	: STD./SLOW
Function	: Sets the time when the power supply to the
	monitor’s circuits (excluding the micro computers)
	starts after the power switch is pressed.
	STD. : The power supply starts approx.
	1 second after the power switch is
	pressed.
	SLOW : The power supply starts approx.
	3.2 seconds after the power switch is
	pressed.

NOTE : When turning on many multi-format monitors simultaneously, it is recommended to use SLOW to control rush current.

Item	: HOUR METER X100h
Number
range	: 000 ~ 655
Function	: Displays the total usage time of the monitor in
	hundred-hour units.

●When the timer passes 655, it returns to 000.

●The timer does not count the usage time under one hour.

2. PICTURE SUB ADJ.

		brightness. Before adjustment, set the BRIGHT
		knob on the front panel to 0.
Item	: CHROMA
Adjustment
range	: –20 ~ 00 ~ +20
Function	: For approximate adjustment of the colour
		density. Before adjustment, set the CHROMA
		knob on the front panel to 0.
Item	: PHASE
Adjustment
range	: –20 ~ 00 ~ +20
Function	: For approximate adjustment of the picture hue.
		Before adjustment, set the PHASE knob on the
		front panel to 0.
Item	: NTSC SETUP
Settings	: 00/7.5
Function	: Sets the level of the input NTSC signal.
		00 : Compliant with 0% set-up signal.
		7.5 : Compliant with 7.5% set-up signal.

NOTE : NTSC SETUP is displayed only when the video input

card is installed and an NTSC signal is input.

Item	: COMPO. LEVEL
Settings	: SMPTE/B75/B00
Function	: Sets the level of the input component signal.

SMPTE : Compliant with M2VTR signals.

B75 : Compliant with Betacam 7.5% set-up signal.

B00 : Compliant with Betacam 0% set-up signal.

NOTE : COMPO. LEVEL is displayed only when a 480/60i, 480/60p, 576/50i or 576/50p signal is input.

Performs approximate
adjustments using the control		<PICTURE SUB ADJ.>
knobs on the front panel. Press		CONTRAST	:00
the	button to display the	BRIGHT	:00
		CHROMA	:00
setting menu illustrated on the		PHASE	:00
		NTSC SETUP	:00
		COMPO.LEVEL	:SMPTE
right.
		sub menu
		reset
NOTE : When the RGB signal		EXIT: MENU ADJUST:- + SELECT:
	is input, only
	CONTRAST and

BRIGHT are displayed. When the PAL signal is input, only CONTRAST, BRIGHT and CHROMA are displayed.

Item	: sub menu
Adjustment range/
Settings	: Same as CONTRAST, BRIGHT, CHROMA,
		PHASE and COMPO. LEVEL/NTSC SETUP.
Function	: Performs CONTRAST, BRIGHT, CHROMA,
		PHASE or COMPO. LEVEL/NTSC SETUP
		settings in a single-line display. The sub menu
		display varies depending on the selected item.
Item	: reset
Function	: Sets the CONTRAST, BRIGHT, CHROMA,
		PHASE and COMPO. LEVEL/NTSC SETUP
		values to factory-preset ones.

14