JVC TM-H1700G manual HOW to Initialize the Setting, Basic Connection Example, Power on

HOW TO INITIALIZE THE SETTING

SCREEN DISPLAY AND SELECTIONS IN THE <SET-UP MENU> RESET MODE

BASIC CONNECTION EXAMPLE

Notes:

• Before connecting your system, make sure that all units are turned off.

• The illustration below shows some examples of different connections. Terminal connections may differ depending on the component connected.

Be sure to refer to the instructions provided with the unit(s) you are connecting.

• Each pair of input (IN) and output (OUT) terminals are bridge-connected.

• If you’re not connecting any equipment to a bridged output (OUT) terminal, be sure not to connect any other cables to the bridged output (OUT)

terminal as this will cause the terminating resistance switch to open (auto terminate function).

• When making a bridge connection, connect the input (IN) and output (OUT) terminals on the monitor to separate video components.

(For example, if both terminals are connected to the same VCR, resonance may occur except during playback. This is caused by the same video

You can set <MENU> and <SET-UP MENU> screen items, picture adjustment items and the volume level to their factory-set (initial) values.

1.Press the Power () switch to turn the power OFF (activate the standby mode).

POWER

<SET-UP MENU> RESET screen

<SET–UP MENU> RESET

Are you sure ? “Yes” then <+> “No” then <MENU>

signal “looping” between the VCRs, and is not a malfunction.)

• Select the video input signal (INPUT A(VIDEO) or INPUT B (VIDEO/Y/C)) with the INPUT SELECT buttons on the front panel. When both

VIDEO B terminals are connected (input) at the same time, the Y/C terminal has priority.

VIDEO A Connection Example (Select Input A (VIDEO))

No.51922

2.While pressing both MENU button and CHROMA/ PHASE button, press the Power () switch to turn

the power ON.

		The <SET-UP MENU> RESET screen is displayed.
		* The screen automatically disappears when no operation
CHROMA MENU	POWER	is performed after about 5 minutes.

Note:

PHASE

● The <SET-UP MENU> RESET screen will not be

displayed if the MENU or CHROMA/PHASE buttons are

pressed for a very short time. Keep pressing them until

Initial settings

Sorts	Functions (Items)	Initialization
		(setting)
screen	SHARPNESS	00
	ADJ. BAR POSI	LOWER
	COLOR TEMP	6500
<MENU>
	COLOR SYSTEM	AUTO
	RUSH DELAY	STD
	ASPECT RATIO	4 – 3
	PICTURE SUB ADJ.
	CONTRAST	00
	BRIGHT	00

Video Camera

Video Monitor

VCR

VIDEO A

Video			Video
(Video signal cable)			(Video signal cable)
	IN	OUT
	VIDEO B		Video
			(Video signal cable)
	IN	OUT
Audio
(Audio signal cable)	IN	Y/C
	OUT
	AUDIO A		Audio
	IN	OUT	(Audio signal cable)

VCR

Video Monitor

ENGLISH

the display screen appears.

3.Setting

Initialization is required.

screen	CHROMA	00
	PHASE	00
	H. POSITION	00
	V. POSITION	00
MENU>
	WHITE BALANCE
	R. CUT OFF	00
	G. CUT OFF	00
UP
	B. CUT OFF	00

	AUDIO B		Audio
 VIDEO B (VIDEO) Connection	IN	OUT	(Audio signal
			cable)
Example (Select Input B (VIDEO))

VOLUME/SELECT

Press the VOLUME/SELECT [+] button.

-
R. DRIVE	00

*Initialization is completed, and the <SET-UP MENU> RESET screen disappears.

Initialization is not required.

<SET	B. DRIVE	00
	CONTROL LOCK	OFF
	STATUS DISPLAY	ON
	REMOTE SYSTEM	MAKE
	INPUT REMOTE	A – B

MENU

Press the MENU button.

* Initialization is aborted, and the <SET-UP MENU> RESET screen disappears.

adjustment	CHROMA	00
	PHASE	00
	CONTRAST	00
Picture	BRIGHT	00
Volume	VOLUME	20

Video Camera	Video
	(Video signal cable)
Video Monitor	Audio
	(Audio signal cable)
	: Signal Flow
VCR

VCR

Video Monitor

12

1-7

13

TM-H1700G