ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS SVENSKA
STORING AND RECALLING PRESETS
TO STORE A PRESET
•Tune to the radio station you wish to enter into a Preset (refer to chapter “Front Panel Controls”; section 8). If the station is transmitting RDS information, the RDS indicator will light up and station initials will be shown in the Display Panel. If a
•To store that station as a Preset, press MEMORY (No. 6). “MEMORY” and the preset section in the display panel will start to flash. If no other button is pressed within 10 seconds, “MEMORY” will stop to flash and the receiver will default to its previous state.
• Press either the (down) or (up) button to select which Preset number you wish to assign to the station (from 1 to 30 on FM and 1 to 10 on AM), shown as a flashing number in the Display Panel, and then press MEMORY (No. 6) again. The Memory light in the Display Panel will go out and the station is now stored in your NAD T742’s memory.
To exit the Memory mode without storing a station, leave all the tuner controls untouched; the Memory mode will automatically cancel itself after 10 seconds. The Memory Presets have a memory
NOTE
You can enter a new station into an unused Preset or
RECALLING A PRESET STATION
To select a Preset station:
•Select the Preset mode by pressing the PRESET/TUNE button (No. 7) until “PRESET” lights up in the display.
• Press either the | (down) or | (up) button (No. 8) until the |
right Preset is found and shown in | the Display Panel. | |
NOTE
Any unused Presets will be skipped.
To “Directly Access” a Preset Station from the Remote Control:
Press the numeric key on the Remote Control (AVR 2) the Preset number selected flashes in the Front Panel display window for 2 secs allowing for a valid second key entry for presets 10 and above.
DELETING A STORED PRESET
You can empty a Preset by deleting the stored information:
•Press MEMORY button (No. 6).
•Press DOWN/UP buttons (No. 8) to select the preset number to be deleted.
•Press the FM MUTE/MODE button (No. 5). The Preset will then be deleted and
You can also store a new station into a used Preset, by simply going through the Preset storing process and placing a new station over the existing one.
REMOTE CONTROL AVR 2 (FIGURE 3.)
The T742 is supplied with the NAD AVR 2 Remote Control. Apart from all the primary operating functions, the AVR 2 Remote Control handset also gives access to functions not available on the front panel of the T742. It also has additional controls to remotely operate NAD T550, L55, T531 and T571 DVD Players. The function of the buttons will change between the T742 Receiver and the NAD DVD Player depending on the position of the RCVR/DVD switch (See 25 below). Shared buttons (buttons that function with the switch in either position) have the receiver function printed on the button itself, with the secondary DVD function printed on the body of the remote handset
Alkaline batteries are recommended for maximum operating life. Two
AAA(R 03) batteries should be fitted in the battery compartment at the rear of the Remote Control handset. When replacing batteries, check that they have been put in the right way round, as indicated on the base of the battery compartment. It will operate up to a distance of 16ft (5m).
1. POWER
Press this button to switch the unit from operating mode to the Stand- by mode and vice versa:
Press this button again to switch the unit on from
2. SLEEP
Press SLEEP to make the T742 automatically switch off after a preset number of minutes. Pressing the SLEEP button once will set the sleep time to 90 minutes, after which the T742 will automatically switch off into Standby mode. Sleep mode is shown on the Display Panel. To adjust the Sleep Delay, press the SLEEP button, each consecutive press will reduce the sleep time in
3. INPUT SELECTION
The EXT 5.1, DVD, SAT VCR and
14