ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS SVENSKA
13. TUNE MODE / RETURN
The TUNE MODE button functions the same as the button of the front panel of the T742, switching between the Tune Mode and the Preset Mode. See complete description in the FRONT PANEL CONTROLS section above.
In DVD mode this button’s function is determined by the individual DVD disc title being played. Refer to the NAD DVD Player Owner’s Manual for more detailed information on this function.
14. OPEN / CLOSE
Opens or closes the loading tray of the DVD player.
15. STOP
Stops play of the DVD player.
16. PLAY
Commences playback of DVD or CD discs loaded in the DVD player.
17. PAUSE / STEP
With CD discs this button pauses playback. With DVD video discs this button places the player in the still picture mode, and each successive press of the button advances (STEPs) the picture by one frame. Press the PLAY button to return to normal playback.
18. SKIP 
/ SKIP 
This button advances or moves back a chapter (DVD) or track (CD) each time the button is pressed.
19. REPEAT
Repeats a program or an entire DVD or CD disc.
20. SCAN 
/ SCAN 
This button scans fast forward or back with DVD or CD discs. Each time the button is pressed the speed of scanning is increased. Press PLAY to return to normal playback.
21. PROGRAM
This button is used to create playback programs on CD discs.
22. AUDIO
This button changes the audio soundtrack language on DVD video discs that support this feature.
23. SUBTITLE
This button changes the subtitle language on DVD video discs that support this feature.
24. CLEAR
This button is used to defeat or clear repeat play programs.
25. RECEIVER/DVD SWITCH
This switch changes the function of the keys on the remote from the T742 RECEIVER commands to the DVD Player commands. This remote includes the codes for use with NAD T531, T571, T550, and L55 DVD Players only.
26. ZOOM
The ZOOM function allows you to enlarge a selected portion of the video image (close up).
27. DVD1 / DVD2 SWITCH
This switch is located inside the battery compartment of the AVR 2, and changes the DVD functions between DVD1 (codes for T550 and L55 DVD Players) and DVD2 (codes for T531 and T571 DVD Players).
SETTING UP THE SURROUND SYSTEM
To obtain the best results in any of the Surround Modes it is important that the T742 is carefully set up. The Dolby Surround system requires that you specify the parameters of your speaker setup so it can properly direct the decoded surround sound signal in the correct proportion to create the most accurate theatrical effect. Dolby also allows for the redirection of bass frequencies to the most appropriate speaker(s). This is also known as “bass management”.
The setup procedure is broken down in three sections:
1Speaker Settings (by Front Panel controls)
2 Channel Delays (by Front Panel controls)
3 Level Settings for correct Channel Balance (by Remote Control handset)
SPEAKER SETTING OPTIONS
SPK SET |
| DELAY |
|
MAIN | LAR or SMA | CEN | |
CENT | LAR, SMA, OFF | REAR | (0 - 15 mS ) Dolby Digital |
|
|
| (15 - 30 mS ) Dolby Pro Logic |
REAR | LAR, SMA, OFF | EXIT |
|
SUB | ON, OFF |
|
|
EXIT |
|
|
|
TO ACCESS THE SPEAKER AND DELAY SETTING ADJUSTMENTS
Pressing the front panel SET UP button (first press) the display will show SPK SET. Rotating the VOLUME/SETUP knob alternately cycles the setting between SPK SET, DELAY , EXIT, and then “wraps” back to SPK SET.
Speaker Settings - First you need to indicate which speakers are connected to your T742. Besides the Main speakers (Left & Right), these can include a Centre, two Surround Speakers and a Subwoofer.
To Adjust Speaker Settings - When Front Panel Display shows SPK SET, pressing the SET UP button on front panel again (second press) will enter the SPEAKER SETTING menu. Rotate VOLUME/SETUP knob to cycle between MAIN > CEN > REAR > SUB > EXIT.
First stop at MAIN and display shows LAR (current setting for FRONT or MAIN speakers). Press the SET UP button again to change the size. Each press of the SET UP button will change the setting for that speaker:
MAIN (Front Speakers) can be selected as LRG or SML
Now rotate the VOLUME/SETUP knob until CEN LAR (current setting for the CENTER speaker) appears in the display window. Press the SET UP button again to change the size. Each press of the SET UP button will change the setting for that speaker:
CEN (Centre Speaker) can be selected as LAR, SMA or OFF.
16