NAD T 765 owner manual About User Names About XM Radio, About RDS

operation

USING THE T 765 – AM/FM/DB/iPod

Choosing the TUNER MODE

The front-panel ‘TUNER MODE’ key is a dual-purpose control. In the normal position, FM Mute FM Stereo icons on the VFD are illuminated, only the stations with a strong signal can be listened to, and the noise between stations is muted.

Pressing the ‘TUNER MODE’ button again (FM Mute FM Stereo icons on the VFD are extinguished) allows distant and potentially noisy stations to be received. Noise is reduced if the FM station signal level is less than the FM Stereo threshold (since mono FM is inherently less noise-prone) though at the sacrifice of the stereo effect.

Note

One can store the same channel in two preset locations - one with TUNER MODE On and another with TUNER MODE Off.

About User Names

About XM Radio

The T 765 is “XM Ready” which means that with the addition of separately sold XM Mini-Tuner CPC-9000 and XM Mini-Tuner Home Dock, it has everything you need to listen to live XM. Everything else is built right in. Just subscribe to the XM service and your T 765 will be ready to receive XM content.

Notes

•Questions? Visit www.xmradio.com

Listeners can subscribe by visiting XM on the Web at www.xmradio.com or by calling (at the time of printing this manual) XM’s Listener Care at (800) 853 9696. Be ready with your Radio ID that can be found on the radio by selecting Channel 0.

•Check with your NAD audio specialist for other versions of XM Mini- Tuner compatible with T 765.

ENGLISH

FRANÇAIS

You can assign an eight character “User Name” to each radio preset, which will show in the front-panel readout whenever that preset is recalled.

Entering User Names

To name a radio preset “NEWS,” follow the procedure as below (The buttons mentioned apply to the front panel’s buttons. The applicable HTR 3 keys also execute the same functions as described).

1Recall the desired radio preset.

2Then, press the ‘MEMORY’ button once and then within five (5) seconds, press the ‘INFO’ button - the readout shows a blinking box.

3	Use the ‘PRESET		/	‘ buttons to select the first character of the
	name (“N” from the alphabetical list).
4	Press ‘TUNE	’ button to select the character and correspondingly
	move forward to the next position. (Press TUNE				to go back to the

previous character). Repeat this process for each character in sequence.

5Press the MEMORY key again to store the User Name and exit the text- entry mode.

About RDS

The Radio Data System (RDS) permits compatible FM A/V Receivers to display text determined by the broadcaster. The T 765 supports two RDS modes, station-name (PS mode) and radio-text (RT mode). However, not every FM station incorporates RDS in its broadcast signal. In most areas you will find from one to several RDS-enabled stations, but it is by no means impossible that your favorite stations will not be broadcasting RDS data.

View RDS Text

When an RDS-enabled FM broadcast is tuned, after a brief delay the “RDS” symbol will illuminate in the T 765’s front-panel readout and the readout’s character section will show its station-name (PS) text: “ROCK101,”for example.

Press the front-panel INFO key to toggle the readout between this and the station’s radio-text (RT) readout, if any, which might scroll song- or artist- name, or any other text of the station’s choosing.

Connecting the XM antenna

1.Plug the end of the XM antenna into the corresponding XM antenna port on the rear panel of the T 765.

2.Press and hold “TUNER MODE” button on the front panel to check the current XM channel’s signal strength as shown in the VFD and OSD. Press “TUNER MODE” again to exit signal strength check.

Refer also to your XM radio’s guide on how to install the XM antenna for optimum signal reception.

Tuning Stations

There are three ways to tune to the XM channel you wish to listen. Make sure to set your HTR 3’s Device Selector to “TUNER” prior to undertaking the

following tuning options. Thebuttons refer to the corresponding keys on the HTR 3. The same keys correspond to the front panel navigation

buttons “PRESET / PRESET / TUNE/ TUNE.”

1.Manual Tuning : Toggle thebuttons to step up or down each

available XM channel. Press and holdfor faster scanning of XM channels. The HTR 3 keys “TUNE/ TUNE” will likewise execute these same functions.

2.Direct Channel Call : Using the numeric keypads of the HTR 3, key-in directly the desired available channel number and it will be automatically tuned.

3.Category : Toggle “TUNER MODE” until “CATXM” and a corresponding category is displayed on the VFD. “CATXM” stands for the categories channels are grouped into – i.e., Country, Rock, Jazz & Blues, etc. Toggle buttons to step up or down the available categories.

After selecting the desired category, use the same steps as that of XM Manual Tuning. Tuning will only be limited to within the selected

category. Toggle thebuttons to choose another category and then tune again.

View XM Information

Toggle ‘INFO’ button to display the XM information of the selected channel such as the artist name, song title, category or any other text as supplied for the channel.

Presets

The procedure for storing XM channels is the same method as stated in the section “Setting Radio Presets” under “Listening to Radio.”

For immediate recall of stored XM presets, toggle “TUNER MODE” button until “P__” (the two blank spaces corresponding to the preset number) is

shown in VFD. Press the front panel’s “PRESET / PRESET” button

or HTR 3’skeys to step up or down the stored presets that can be a combination of AM, FM and XM channels.

ESPAÑOL

ITALIANO

SVENSKA NEDERLANDS DEUTSCH

РУССКИЙ

31