Sharp AR-C160 operation manual Installation Requirements

Page 14

CHAPTER1 GETTING STARTED Installation requirements

INSTALLATION REQUIREMENTS

To ensure safety and proper machine performance, please note the following before initial installation and whenever the machine is to be relocated.

1. The copier should be installed near an accessible power outlet for easy connection.

2.Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

Also make certain the outlet is properly grounded.

3. Do not install the machine where it is: ● damp or humid,

●exposed to direct sunlight,

●extremely dusty,

●poorly ventilated,

●subject to extreme temperature or humidity changes (e.g., near an air

conditioner or heater).

4.Ensure that the area chosen for the machine location is level.

5. Be sure to allow the required space around the machine for servicing and proper ventilation.

23-5/8"

(60 cm)

A small amount of ozone is produced within the copier during operation. The emission level is insufficient to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration. However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

11-13/16"

(30 cm)

11-13/16"

(30 cm)

23-5/8"

(60 cm)

1-2

Image 14

Contents AR-C160 Easily accessible For Your RecordsColor Copying with Special Features Color Copy SamplesNeg./Pos. Reverse See Multi-page Enlargement See Adjustments for Color Copying Printed photo modeRGB Adjust See Sharpness See Color Balance See Brightness/intensity/contrast See Original Brightness + Intensity + Contrast +Contents Using this Manual IntroductionChapter Installation Requirements Battery Disposal Safety Precautions Power on and OFF Become possibleSleep mode Power on and OFFPower save modes Preheat modeScreen for the information categories will appear Press the Information key in the standby modeInformation Function Selection of function Using the Touch PanelHow to use the touch panel Using the Touch Panel Function setting iconsPrinting documents from the computer Copy Mode and Print ModeBasic screen of the print mode will appear Check the operation panel to confirm that the on LineHow to select the paper type for the bypass tray Copy Mode and Print ModeUsing the operation panel in the print mode To return to the printer basic screen, press the return keyGeneral operation steps for using the scanner Making Copies Auditing Accounts Copy Start key is pressedUse the 10-key pad to enter the desired number Copies Sided copies of 1-sided originalsClose the document cover Making Copies Copying fromPress the Color Copy Start key or Black Copying from the Document GlassSided copies from 1-sided originals Copy the originals in reverse order When making color copies in the duplex mode or making B/WCopy the reminder of the originals in reverse order Using the Radf Stream feeding modeSet the originals face up in the document feeder tray Using the RadfAdjust the original guides to the size of the originals If the number of originals is not known, select Number Originals key orOriginals key on the touch panel, then proceed to Press the Color Copy Start Key or Black Copy Start keyAdjust the original guides to the size of the originals Sided copies from 2-sided originalsOriginal 2-sided Copies 1-sided Optional document feeder tray REDUCTION/ENLARGEMENT/ZOOMAutomatic selection Select the paper tray with the desired paper sizeREDUCTION/ENLARGEMENT/ZOOM Manual selection129% Special Papers manual feed Two-sided copying with bypass tray Original image type Exposure AdjustmentsAutomatic Press the Exposure key on the touch panel Exposure AdjustmentsIf TEXT/PRTD. PHOTO, Text or TEXT/PHOTO Has been selected in , select Auto or ManualJOB Memory Storing a job programRecalling a job program JOB MemoryDeleting a stored job program Interrupting a Copy RUN Special Functions Press the Copy Ratio key on the touch panel XY ZoomPress the XY Zoom key Following screen will appearCopy ratio in the vertical Y direction will be highlighted XY ZoomPress the Y key Special Modes screen will appear Margin ShiftPress the Special Modes key Press the Margin Shift key on the touch panel Select the desired shift amounts usingMargin Shift Select the shift directionEdge + center erase Setting screen for Erase will appearErase Press the Erase key on the touch panelErase Select the desired erase modeErase on the touch panel. The selected erase mode will be HighlightedDual page Copying Ensure that the desired tray is selected Dual page CopyingInformation 4 Press the OK key Centering Bottom directionCentering key will be highlighted CenteringPress the Centering key on the touch panel Transparency Inserts key will be highlighted PanelPress the Transparency Inserts key on the touch Load transparency film into the bypass tray Transparency Film with Insert SheetsInfor 4 Press the OK key Key or Black Copy Start keyDuplex selection window CoversPress the 2-SIDED Copy key and select the desired Not Select cover placementCovers Press the upper OK keyColor Adjustments Color Adjustments menu will appearSelect a color to be adjusted Color AdjustmentsPress the RGB Adjust key on the touch panel Key to weaken the colorSetting screen for Sharpness will appear Press the Sharpness key on the touch panelPress the upper OK key.SPECIALFUNCTIONS Coloradjustments Setting screen for Suppress Background will appear Press the Suppress Background key on the touchLevel Suppression levelUse the and + keys to select the desired background Color Balance Press the Color Balance key on the touch panelColor balance settings Brightness /INTENSITY /CONTRAST Select BRIGHTNESS, Intensity or Contrast on the touch panel Select the desired item to be adjustedUse the and + keys to adjust the level of the selected item Image Edit menu will appear Image Editing FunctionsPress the Image Edit key on the touch panel Select the desired color Image Editing FunctionsPress the Single Color key on the touch panel Selected color key will be highlightedMode, the black and white areas will be reversed Press the Image Edit key on the touch panelPress the NEG./POS. Reverse key on the touch Relation to the NEG./POS. ReverseReverse C D Press the Mirror Image key on the touch panel Mirror Image key will be highlightedPlace the original on the document glass Place 2 ½ x 4 and 2 ½ x 2 ½ originals as shown belowSetting screen for Photo Repeat will appear Select the desired repeat typeOriginal will be copied onto 12 x 18 size copy paper To 100% when this function is selected11 x 17 FULL-BLEED Optional document feeder cannot be used with this functionPress the 11 x 17 FULL-BLEED key on the touch panel 11 x 17 FULL-BLEED key will be highlightedSelect the desired enlargement size Setting screen for MULTI-PAGE Enlargement will appearPress the MULTI-PAGE Enlargement key on Touch panel PanelCancel OK Original Size & Orientation Select the original sizeSetting screen for Image Edit selections will appear Either one or both can be setAdjust the original size on the Original Size tab Press the Extra Size key on the touch panelRefer to page 2-11 for the Auto Image function Press the upper OK key on the touch panelPress the Auto Image key on the touch panel Supplies Loading copy paper PaperTypes and sizes of copy paper For best results, use only Sharp recommended paperPush the paper tray firmly back into the copier PaperLoading paper in the paper trays Tray holds 500 sheets of 20 lb. bond paperChanging the copy paper size in the tray Adding Toner Open the front coverIt will take about 40 seconds for the cartridge to empty Adding TonerLeft example shows the toner hopper of black toner Supplies Adding toner Open the toner collecting container cover Used Toner DisposalDisengage and remove the container from the copier Push once on the door to unlatch and open itStore the supplies in a location that is Storage of SuppliesProper storage Store copy paper in the wrapper and lying flatPage Copier TROUBLE? Misfeed in the optional Radf When a misfeed occurs, the copier will stopMisfeed Removal Open the feeding roller cover and pull the original gently Misfeed RemovalMisfeed in the bypass tray Open the exit roller cover and gently pull the original outTurn the transport lever to the left Do not pull out the paper transport in this stepOpen the right side covers Misfeed in the paper traysClose the front cover If the paper cannot be seen from the side, pull outCheck to see if any paper is misfed in the exit area Misfeed in the transport area, exit area and fusing areaOpen the front cover Turn the transport lever to the left Close the paper tray and the side coversGently close the upper right side cover Remove the misfed paper Misfeed in the optional duplex module Push the duplex module back into the copier Slide the paper guide if neededMaintenance Required When the message Ready to COPY. Maintenance RequiredToner Collecting Container of Transfer Unit Troubleshooting Example TroubleshootingSelf-diagnostic function General Information Part Names and Functions Part Names and Functions Black Copy Start key and indicator Interrupt key and indicator pColor Copy Start key and indicator LCD touch panelInformation key p Custom Settings keyInitial settings Sided Copy keyUser Maintenance Document glass and document coverContrast of the touch panel can be adjusted as below ContrastSpecifications CopierDuplex Module optional SpecificationsReversing Automatic Document Feeder optional Emission Concentration measurement according to RAL UZ62 Printing mode Standby modeAcoustic Noise Emission measurement according to ISO7779 Optional Equipment System Configuration BIN Staple Sorter AR-SS2 Part NamesUsing the staple sorter BIN Staple Sorter AR-SS2Sorter Capacity Using the document glass Staple sortUsing the optional Radf Up to 20 sets can be madeManual stapling Set of copies will be stapledStaple cartridge replacement Remove the empty staple cartridge from inside Staple boxRemove the rear paper and tape from the cartridge Staple jam removal Return the lever to its original positionBIN Staple Sorter AR-SS2 Slide the sorter back toward the copier and latch it into Copier will stop when a misfeed occursMisfeed removal 17 ~ 28 lbs 2 x SpecificationsPaper Weight 13 ~ 28 lbs 11 x 12 xPaper size 2 x Paper weight 15 lbs. to 28 lbs Large Capacity Tray AR-LC2NFan the copy paper When the button lamp goes out, pull the paper tray outLarge Capacity Tray AR-LC2N Load the paper onto the feed tableCapacity tray Remove any misfed paper from the copier and the largeRemove the misfed paper Gently push the tray back into place Finisher AR-FN4 Finisher AR-FN4 Offset modeNON Offset mode Offset stackStaple print Printed output will be stapledWhen the staple cartridge is empty, the message Slide Replace the staple as followsFinisherAR-FN4 Staple jam removal Finisher AR-FN4 Misfeed removal Finisher AR-FN4 Page Page Sharp Corporation

Related manuals

Manual 38 pages 36.08 Kb