Sharp LL-T2000A operation manual For Windows98, For Windows2000

Connecting the monitor and turning the monitor on and off

Installing set-up information and the ICC profile (for Windows)

Depending on the computer or OS, it may be neces- sary to use the computer to operate the installation of monitor set-up information etc. If so, follow the steps below to install the monitor set-up information. (Depending on the computer type, command names and methods may differ. Please follow the compu- ter’s own operation manual while reading this.)

Note:

This explanation assumes that the floppy disk drive is "A drive". If the floppy disk drive of your computer is not "A drive", please read the below substituting the floppy disk drive you are using in place of "A drive" or "A".

About ICC profiles

An ICC (International Color Consortium) profile is a file that describes the color characteristics of the LCD monitor. By using an application that works together with an ICC profile, a high color resolution can be realized.

Notes:

-Windows 98/2000/Me use the ICC profile.

-When the storing Windows 98/2000/Me set- up information, the ICC profile is also installed. If you would like to install the ICC profile only, please refer to Installing the ICC profile on the following page.

-When using the ICC profile, please set the [WHITE BALANCE] to [STD] and set the [COLOR MODE] to [OFF].

[ For Windows 95 ]

Installing monitor set-up information into Windows 95. This explanation assumes that the floppy disk drive is "A drive".

1.Place the Utility Disk (provided) into the computer's A drive.

2.Click on the [Start] button. From [Settings], choose [Control Panel].

3.Double click on [Display].

4.Click on [Settings], [Advanced Properties], and [Monitor], then [Change].

5.Click on [Have Disk], confirm that [Copy manufacturer's files from:] is [A:] then click [OK].

6.Confirm that the monitor details are selected, and click [OK].

7.Check that the monitor details are displayed, then click [Apply].

8.Click [OK], and close the window.

9.Remove the Utility Disk from the A drive.

[ For Windows98 ]

Installing monitor set-up information into Windows 98, and setting the monitor's ICC profile as a prede- termined value.

This explanation assumes that the floppy disk drive is "A drive".

If the "Add New Hardware Wizard" has appeared:

1.Place the Utility Disk (provided) into the computer's A drive.

2.Click [Next].

3.Check [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next].

4.When [Models] is displayed, click on [Have Disk], confirm that [Copy manufacturer's files from:] is [A:], and click [OK].

5.Confirm that the monitor details are selected, then click [Next], [Next], and [Finish]. If the "Add New Hardware Wizard" appears, repeat the installation commands beginning from 2 above.

6.Remove the Utility Disk from the A drive.

If the "Add New Hardware Wizard" has not ap- peared:

1.Place the Utility Disk (provided) into the computer's A drive.

2.Click on the [Start] button. From [Settings], choose [Control Panel].

3.Double click on [Display].

4.Click on [Settings], [Advanced] and [Monitor].

5.In [Options], check [Automatically detect Plug & Play monitors] and click on [Change].

6.Click [Next].

7.Click on [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next].

8.When [Models] is displayed, click on [Have Disk], confirm that [Copy manufacturer's files from:] is [A:], and click [OK].

9.Confirm that the monitor details are selected, then click [Next], [Next], and [Finish].

10.Check that the monitor details are displayed, then click [Apply].

11.Click [OK], and close the window. 12.Remove the Utility Disk from the A drive.

[ For Windows2000 ]

Installing monitor set-up information into Windows 2000, and setting the monitor's ICC profile as a predetermined value.

This explanation assumes that the floppy disk drive is "A drive".

13