TANDBERG D13187-03 user manual Dataport Configuration, Baudrate, Parity, Databits, Stopbits

Page 45

TANDBERG Gateway

Configure the Gateway

 

 

 

Dataport Configuration

To configure the Data port on the gateway, open ‘Dataport’ as shown in the figure below.

NOTE

WHEN CONNECTING TO A PC

THE CONNECTING CABLE MUST

BE A STRAIGHT THROUGH

RS232 CABLE.

Dataport Configuration is used to configure the RS 232 serial port on the gateway. If you want to connect a PC to the dataport, you must ensure that the PC and the gateway are identically configured.

Configuration

Baudrate

Possible values are: 1200 bps, 2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps 56600 bps and 115200 bps.

Parity

Select ‘None’, ‘Odd’ or ‘Even’.

Databits

Select 7 or 8 databits.

Stopbits

Select 1 or 2 stopbits.

Save

Press ‘Save’ to activate the new settings.

NOTE

THERE ARE NO HARDWARE OR SOFTWARE

HANDSHAKE OPTIONS. MAKE SURE THE

PC HANDSHAKING IS TURNED OFF.

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents
Gateway Tandberg Gateway Trademarks and copyright Equipment Markings Operator Safety SummaryContents Index AppendicesIsdn Services IP Services and ProceduresIntroduction SecurityVideo Quality PresentationsInteroperability Management Interfaces Network and FeaturesFront view Tandberg GatewayGateway Capacity typical scenarios 4 Mbps option Rear viewInstallation PrecautionsUnpacking Rack Mounting optional Installation site preparationsPower cable Connecting cablesIsdn PRI cables LAN cableGateway Configuration Gateway start-up Accessing the gatewayCall Overview Using the GatewayGW Calls Idle No call is activeIP/H.323 Call connected is using the H.323 protocol over IP Call connected is using the H.320 protocol over IsdnSource / Destination Encryption Secure conferenceTFStatus ActionsDisconnect Gateway Call Call TransferUsage Isdn NumbersNumbers IVR Dial from IsdnIVR + TCS-4 Hotline Sequence of ServicesDial from IP ServicesDial out to 2x64k Isdn H.221 Bridging IP Islands Expressway Solution Page Add new entry Manage the Phone BookEdit Entry CancelDelete SavePRI Status View System StatusPRI Alarms Example of Location CodesExample of Isdn Cause Codes Status System InformationGW IP Address Shows the IP address of the gateway Available Resources Configure the Gateway System ConfigurationPRI Configuration Parallel Dial PRI ProtocolSending Complete Send Own NumberPRISM1, PRISMII, Wats Number Range Start Interface ConfigurationNumber Range Stop T1 Cable LengthMax Channels Channel HuntingLow Channel High ChannelConfiguration IP ConfigurationIP Address Assignment IP Ethernet Speed Static IP Subnet Mask Static IP Address Static IP Gateway RestartConfiguration GatekeeperDirect Authentication ID, Password Authentication ModeQuality of Service Gatekeeper IP AddressMin. Cost Will choose the route with minimum cost QoS Mode ConfigurationBaudrate Dataport ConfigurationParity DatabitsSnmp Community Name Snmp ConfigurationSnmp Trap Host 1, 2 System ContactPassword Miscellaneous ConfigurationSnmp Security alert Install Software Software UpgradeSystem Information Software OptionFollowing can be specified File ManagementExtension Dial Isdn Dial In ConfigurationDial In Number Dial In Max. Bandwidth2nd Dial In Number Allow Incoming PhonecallsDirect Inwards Dialing No. Significant DigitsPrefix E.164 Services ServiceDescription Isdn Prefix Max. RateRestrict Save ChangesSignal Busy on Load Natural Video Gateway FeaturesCustom Video Formats Duo Stream Duo Video / H.239Encryption Appendices Appendix 1 Using the file systemAppendix 2 Declaration of Conformity Appendix 3 Capacity Gateway capacity calculationGateway capacity typical scenarios 4 Mbps version Index Tandberg Gateway Index
Top Page Image Contents