Sharp XR-30S, XR-30X, XR-40X operation manual Resetting the Lamp Timer

Page 56

Regarding the Lamp (Continued)

4 Remove the lamp unit.

Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time,

keep the lamp unit horizontal and do not tilt it.

5

6

Insert the new lamp unit.

 

 

 

 

 

 

 

 

 

 

Securing

 

screws

 

Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.

Replace the lamp unit cover.

• Align the tab on the lamp unit cover (1) and place it while pressing the tab

(2) to close it. Then tighten the user ser- vice screw (3) to secure the lamp unit cover.

Info

• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is con- nected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or ex- plode.

1Connect the power cord.

Plug the power cord into the AC socket of the projector.

2Reset the lamp timer.

While simultaneously holding down MENU/HELP, ENTER and R on the pro- jector, press STANDBY/ON on the pro- jector.

“LAMP 0000H” is displayed, indicating that the lamp timer is reset.

AC socket

STANDBY/ON button

ENTER button

R button

MENU/HELP button

52

Image 56
Contents XR-40X XR-30X XR-30S Model No Serial No Iii Page IntroductionENGLISH Information Using the Menu Screen For Future ReferenceContents Reference Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents See Replacing the Lamp onOther connected equipment Using the projector in other countriesTemperature monitor function Accessories Optional accessoriesPart Names and Functions ProjectorRear View TerminalsStandby button For putting Projector into Standby mode Buttons For switching to Respective input ModesAdjustment Setting screens,Inserting the Batteries Remote control can be used to control Remote control signal transmittersUsable Range Projector within the ranges shown IllustrationSetup and Projection Quick StartProjector Control Upper sideOn the remote Setting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount Setup120 Projection PRJ ModeExample Normal Mode Picture Size Screen Size and Projection Distance Normal ModeStretch Mode Connecting the Projector to Other Equipment You may need other cables or connectors not listed belowConnecting the Projector to Other Equipment RGB Controlling the Projector by a Computer Connecting the Power CordAC socket To AC outlet Power cord supplied Lamp indicator Power indicator STANDBY/ON button Turning the Projector On/OffTurning the Projector on On-screen display confirmation messageAbout the Setup Guide Adjusting the Projected Image Adjusting the FocusAdjusting the Picture Size Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelPress Keystone to enter the Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionAdjustment buttons P/R/O/Q Return button Keystone button On-screen display Keystone Correction modeSwitching the Input Mode Adjusting the VolumeButtons AV Mute button VOL +/- Volume buttons On-screen displayResize Mode Press ResizeVideo Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreeze button Picture Mode button Auto Sync button Freezing a Moving ImageUsing the Remote Control as the Wireless Computer Mouse When moving the cursorWhen left-clicking When right-clickingComputer Component DVI Component, S-VIDEO, Video input Menu ItemsComputer RGB, DVI RGB input Items you can set with the Help menu Help menu nUsing the Menu Screen Menu Selections AdjustmentsPress Q or O and select Picture to adjust Example Adjusting BrightTo adjust the projected image while watching it Press P or R and select Bright to adjustPress O or Q to adjust the item selected Press EnterPicture Adjustment Picture Menu Example Picture screen menu for Computer RGB inputAdjusting the Image Menu operation nSee page 28 for details of Keystone Correction Button Adjusting the Projected Image SCR ADJ MenuYou can move the projected image vertically Adjusting the Projected Image SCR ADJ Menu Adjusting the Projector Function PRJ ADJ Menu Adjusting the Projector Function PRJ ADJ Menu This function changes the fan rotation speedATaking the Keylock off Enter the same keycode in Re- confirmLocking the Operation Buttons Press Oor Qto select Help, then Troubleshooting with the Help MenuUtilizing the Help Menu Functions Maintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Replacing the Lamp Regarding the LampLamp Remove the lamp unit cover Removing and Installing the Lamp UnitDisconnect the power cord Resetting the Lamp Timer Connecting Pin Assignments GNDProjector Computer RS-232C Specifications and Command Settings Return code 0DHCommands RGB PAL Control Contents Return Computer Compatibility Chart PC/MACTroubleshooting 21-2447-49 For Sharp Assistance Specifications Dimensions Index
Related manuals
Manual 71 pages 56.11 Kb