Vivitek D5500 manual Replacing the Lamps

Page 90

DLP Projjecttor – User’s Manuall

Replacing the Lamps

When a lamp reaches the end of it’s usable life, the following message is displayed. Replace the lamp.

The projection lamps should be replaced when they burn out. They should only be replaced with a certified replacement part, contact your local dealer if unsure.

Note:

1.Lamps are positioned differently. Take care not to force the lamps when replacing.

2.Installation of both lamp modules (Lamp 1 and Lamp 2) is required to operate the projector in dual or single lamp mode. If only a single lamp module is installed, the projector's lamp will not turn on and will appear as a lamp failure.

3.Lamps last approximately 2000-2100 hours (2500-2600 hours in Eco mode) and the End of lamp life message is displayed during the lamps' final 100 hours of operational life. Please replace during 2000-2100 hour.

Important:

1.The lamp contains a certain amount of mercury and should be disposed of according to local ordi- nance regulations.

2.Avoid touching the glass surface of the new lamp: doing so may shorten its operation life.

Caution:

Lamp Handling Precautions

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

Lamp life may differ from lamp to lamp and according to the environment of use. There is no guar- antee of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than other similar lamps.

If the projector indicates that the lamp should be replaced, i.e., if LAMP 1 and/or LAMP 2 light up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow care- fully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with LAMP 1 and/or LAMP 2 lighted may increase the risk of lamp explosion.

A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

If a lamp explodes, the following safety precautions should be taken:

Disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cool- ing air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

83

Image 90
Contents Copyright Important Safety Information Preface Main Features Table of Contents Using ON-SCREEN Display Regulatory Compliance Packing Checklist IntroductionFront-right View Views of Projector PartsTop view Bottom view Top Features Lens ControlsPower OSD Controls and Status LEDsDLP Projector User’s Manual Terminal Panel Features 100Power Switch Remote Control Parts DLP Projector User’s Manual Remote Control Remote Control Operating RangeProjector and Remote Control Buttons Setup and Operation Inserting the Remote Control BatteriesInstalling or Removing the Optional Lens Removing the Existing Lens From the ProjectorInstalling the New Lens Pull out the existing lens slowlyThrow Distance and Screen Size Diagonal Width HeightDiagonal Width Height Distance Installing the Optional Color Wheel DLP Projjecttor User’s Manuall DLP Projjecttor-User’s Manuall Connecting Your PC or Macintosh Computer Making ConnectionsConnecting an External Monitor Connecting Your DVD Player with Component Output Connecting Your VCR or Laser Disc Player Projecting AN Image Basic Operation Turning on the ProjectorDLP Projjecttor-User’s Manuall Selecting an Input Source Adjusting Picture Position Manually Adjusting the Picture Position and Picture SizeLens Shift Adjustable Range From the Remote Control Unit DLP Projjecttor User’s Manuall Adjusting the Projector Level Adjusting the Image Using Auto Optimizing an RGB Image AutomaticallyAdjusting Volume Up and Down Turning off the Projector About Direct Power Off After UseTurning Off the Image and Sound Freezing a PictureAdjusting by Using the OSD Control Panel Adjusting the Focus/Zoom ManuallyChanging Lamp Mode by Using the Projectors OSD Control Panel Changing Lamp ModeGetting Information Adjusting Position/Total Dots/Fine Sync Correcting Keystone by Using the Remote Control Higher resolution than XGA narrows the adjustable range Locking the Projector Preventing the Unauthorized Use of the ProjectorUnlocking the Projector Using the Kensington Lock Using the Physical LockUsing the Menus Navigating the OSDDLP Projjecttor-User’s Manuall Menu Tree DLP Projjecttor-User’s Manuall Menu Elements TitleHighlight Slide bar Exit Radio buttonInput Menu Descriptions and Functions LabelAdjust Menu Descriptions and Functions Image menuImage options menu Screen OverscanVideo menu Noise reduction 3D Y/C separationProgressive Color matrix FilmDetail Setting Menu Descriptions and Functions BasicGamma White balance Color correction Setting Menu Descriptions and Functions Lamp mode KeystoneLamp control Lamp interval LanguageInstallation Ceiling & Rear Communication speedDisplay time BackgroundPIN Code Lock DynamicBlack Network SettingKey lock RC sensorStandby mode PC controlNetwork setting DhcpOption Power management Screen triggerFan control Default input select MessageSearch mode Filter warningUsage time Information Menu Descriptions and FunctionsInput Network Version Reset Menu Descriptions and Functions Cleaning the Cabinet Cleaning the LensCleaning the projector Cleaning the Filters Replacing the Lamps DLP Projjecttor-User’s Manuall DLP Projector User’s Manual Resetting the Lamp Time Counter Indicator Messages TroubleshootingPower LED Common Problems and Solutions Tips for TroubleshootingLamp LEDs Lamp Problems Image ProblemsRemote Control Problems Audio ProblemsHaving the Projector Serviced Optical Specifications Projector SpecificationsElectrical Specifications Mechanical Specifications Environmental ConsiderationsOptional Parts Cabinet Dimensions Pin Assignments of Mini D-Sub 15 Pin Input Connector PIN Number RGB Signal Analog YCB CR SignalCompatible Input Signal List ATE KH ZPC Control Codes and Cable Connections Functional Execution Command Table Command FunctionStatus Read Command Table Screen Trigger Overview Handling of the Address for Operation by Using a BrowserOperation Using Http Browser Preparation Before UseConfiguring Network Settings DomainTest Mail Structure of the Http Server Http// the projectors IP address /index.html105 Canada Safety CertificationsFCC Warning EN 55022 Warning