Sharp PG-C45S operation manual Displaying the Break Timer, Displaying and Setting the Break Timer

Page 63

Displaying the Break Timer

This function can be used to show the remaining time for break during meeting.

Displaying and Setting the Break Timer

1 Press . The break timer starts to count down from 5 minutes.

2 When “” is displayed, press

', " , \ or to set the break timer.

•You can set anywhere between 1 and 60 minutes (in 1 minute units).

•The break timer starts to count down as soon as ' , " , \ or is pressed.

3 Press to cancel the break timer.

Note

•Auto Power Off will be temporarily dis- abled during the break timer.

When no input signal is detected for more than 15 minutes, the projector will auto- matically shut off if the break timer has elapsed.

•The break timer will be displayed on the startup image. To change the screen dis- played during the break timer, change the setting of “Startup Image” (see page 68).

', ", \,

buttons

BREAK TIMER button

"On-screen Display

Easy to Use Functions

-59

Image 63

Contents PG-C45S Model No. PG-C45S Serial No Special Note for Users in the U.K Page Introduction Product Disposal New Edge Up-Scaling Outstanding FeaturesColor Management System Noise ReductionContents Appendix Power-Cord Protection CleaningAccessories Power SourcesWall or Ceiling Mounting Damage Requiring ServiceReplacement Parts Safety CheckRest your eyes occasionally Avoid locations with high or low temperatureUsing the projector in other countries Temperature monitor functionFor Macintosh To install Acrobat Reader from the CD-ROMFor other operating systems For other languages For WindowsProjector Front and Top View Part NamesProjector Rear View Using the Kensington LockRemote Control Front View Remote Control Top ViewPart Names Inserting the Batteries Using the Remote ControlAvailable Range of the Remote Control When using the remote controlAccessories Supplied accessoriesOptional cables Connections and Setup An audio cable commercially available See Connecting the Projector to Other DevicesBefore Connecting This projector can be connected toConnecting the Power Cord Ferrite core Connecting to a Computer Using the RGB CablePlug and Play function when connecting to a 15-pin terminal Connecting to Video Equipment Cable Connecting to Component Video EquipmentConnecting to an Amplifier or Other Audio Components Connecting to an AmplifierControlling the Projector by a Computer Watching Images on Both the Projector and a Monitor Connecting to a MonitorUsing the Wireless Pre- sentation Function Press or while using presentation software on your computerButton Connecting the Remote Control to the Projector Using as a Wired Remote ControlUsing the Adjustment Feet SetupAdjusting the Lens Focus ring Zoom knobOut Zoom Throw Distance Setting up the ScreenNormal Mode Stretch ModeScreen Size and Projection Distance AN-C12MZ Throw ratio 11.18 to Projection from behind the screen Projecting a Reversed/Inverted ImageBasic Operation Image Projection Basic ProcedurePlug the power cord into the wall outlet Press on the projector or on the remote controlVolume buttons Press , , or on the remote control to select the Input modePress \ or to select Lan Selecting the On-screen Display LanguagePress to temporarily turn off the sound PressPress or to select the de- sired language, and then press Test pattern Press , , \ and to adjust the Keystone correctionCorrecting Trapezoidal Distortion Keystone button Enter button Undo button ButtonsUndo button Sub menu Menu Bar ItemsMain menu Sub menu Input 3 / 4 ModeUsing the Menu Screen Menu Selections AdjustmentsMenu Bar Main Menu Enter button Buttons Menu button Press \ or to select the menu you want to adjust Press or to select the item you want to adjustPress \ or to adjust the item selected Menu Selections Settings Press or to select the item you want to setEnter button Buttons Menu button Cursor shifts to the sub menu Adjusting the Picture Adjusting Image PreferencesSelecting the Signal Type Progressive Mode Adjusting Computer Images When Auto Sync is OFFSaving Adjustment Settings Selecting Adjustment Settings Special Mode SettingsChecking the Input Signal Auto Sync button Auto Sync AdjustmentAuto Sync Display Function Screen display during Auto SyncEasy to Use Functions Selecting the Picture Display Mode Switching the Picture Display Using Different Input SignalsResize button Screen display of the picture display mode Video Displaying a Still Image Freezing a Moving ImageFreeze button Enlarging a Specific Portion of an Image Displaying an Enlarged Portion of an ImageButtons Enlarge Enlarge/ Reduce buttons Gamma Correction Function Adjusting Gamma CorrectionDisplaying Dual Pictures Pict in Pict Displaying the Inset PicturePress to move the inset pic- ture This function can be used to display a black screen Black Screen FunctionBlacking out the Pro- jected Image To return to the original projected image, press againButtons Break Timer button Displaying the Break TimerDisplaying and Setting the Break Timer Press to cancel the break timerSelecting the Target Color Selecting the Color Reproduction ModeSetting the Brightness of the Target Color Setting the Chromatic Value of the Target ColorSetting the Hue of the Target Color Overview of All Color Settings Resetting User-Defined Color SettingsSetting on/off the Inter- nal Speaker Setting the Audio Output TypeSetting on/off the Internal Speaker Setting the Audio Out- put TypeAuto Search Function Using Auto SearchTurning Off On-screen Display Setting On-screen DisplayVideo Digital Noise Reduction DNR System Reducing Image NoiseSetting the Video System Setting the Video SystemSaving Projected Images Capturing the ImageDeleting the Captured Image Selecting a Startup Image Setting a Background ImageSelecting a Startup Image Selecting a Background ImageSelecting the Economy Mode Setting the Power Save ModeMonitor Out/RS-232C Off Function Checking the Remaining Lamp Life Percentage Automatic Power Off FunctionSelecting the Economy Mode Displaying the Remaining Lamp Life PercentageLocking the Operation Buttons on the Projector Setting the Projection ModeSetting up the Keylock Reversing/Inverting Projected ImagesCanceling the Keylock Setting Selecting the Transmission Speed RS-232CSelecting the Transmis- sion Speed RS-232C Entering the Password Setting up a PasswordIf You Forget Your Password Changing the PasswordEntering the Keycode Setting the Anti-TheftEnter the same 4-digit keycode in Reconfirm Changing the KeycodeReturning to Default Settings Initializing the SettingsOverview of All Menu Settings Displaying the Adjustment SettingsAppendix Cleaning the exhaust and intake vents MaintenanceCleaning the projector Cleaning the lensRemove the bottom filter cover Cleaning and replacing the bottom air filterTurn off the power and discon- nect the power cord Replacing the Air FilterClean the air filter Replace the air filterReplace the filter cover Maintenance Indicators About the temperature warning indicatorAbout the lamp replacement indicator Maintenance Indicators Regarding the Lamp LampReplacing the Lamp Change the air filter Removing and Install- ing the Lamp UnitPress on the projector to turn off the power Disconnect the power cordResetting the Lamp Timer RGB Input Component Input Connecting Pin AssignmentsCommunication conditions RS-232C Specifications and Command SettingsCommands PC controlRS-232C Specifications and Command Settings Options Control Contents Function and transmisson codes Wired Remote Control Terminal SpecificationsSpecifications of wired remote control input Sharp remote control signal formatComputer Computer Compatibility ChartTroubleshooting Troubleshooting For Sharp Assistance Ntsc 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM SpecificationsUnits inches mm DimensionsAdvanced intelligent compression Glossary100 Index101 StretchSharp Corporation

PG-C45S specifications

The Sharp PG-C45S is a compact, high-performance projector that caters to the needs of professionals and educators alike. This versatile device is designed for presentations, training sessions, and classroom use, delivering impressive image quality that enhances any visual experience.

One of the standout features of the PG-C45S is its high brightness rating of 4,500 ANSI lumens, which ensures clear visibility even in well-lit environments. This feature makes it ideal for conference rooms and classrooms where lighting conditions can vary. The projector uses DLP (Digital Light Processing) technology, which enhances color accuracy and sharpness, providing vibrant and true-to-life images with a resolution of 1024 x 768 (XGA).

The PG-C45S boasts a contrast ratio of 2,000:1, which contributes to deeper blacks and brighter whites, creating a dynamic visual experience that captivates audiences. This projector supports various resolutions, making it compatible with a wide array of input sources, including laptops, DVD players, and gaming consoles.

Furthermore, the Sharp PG-C45S features a range of connectivity options, including HDMI, VGA, and composite video inputs, providing flexibility for different setups. It is equipped with an integrated 10-watt speaker, which delivers clear audio for presentations without the need for additional sound equipment.

The projector also incorporates advanced features such as vertical and horizontal keystone correction, allowing users to easily adjust the image to fit various screen sizes and setups. The easy-to-navigate on-screen display simplifies the setup process, making it user-friendly for those who may not be tech-savvy.

In terms of portability, the PG-C45S is lightweight and designed for easy transport, making it suitable for professionals who need to take their presentations on the go. Its durable construction ensures longevity, while an eco-friendly mode reduces power consumption and extends lamp life, thereby lowering the total cost of ownership.

In conclusion, the Sharp PG-C45S is a reliable and feature-rich projector suitable for a variety of environments. With its impressive brightness, excellent image quality, and user-friendly features, it is a compelling choice for anyone looking to enhance their presentation experience.