Vidikron Vision 15ET/CineWideTM operation manual Adjusting the Lens Height and Angle

Page 48

Installation

3.Secure the lens (with the mounting bracket attached) to the Lens Base Plate (6) using the swell latches.

Tip

To avoid clipping the corners of the image, position the anamorphic lens

as close as possible to the primary lens.

Adjusting the Lens Height and Angle:

1.Project a white field on the screen.

2.Loosen the four Height/Pitch Adjustment Screws just enough to allow vertical movement of the lens assembly.

3.Slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen:

Too Low

Correct position

Too High

4.Then, adjust the anamorphic lens angle so that the projected image is rectangular:

Correct Lens Angle

Incorrect Lens Angle

The anamorphic lens will almost always be angled with respect to the projector; this is normal.

5.When the height and angle are properly set, tighten the Height/Pitch Adjustment Screws to secure the lens in place.

There may be some pincushion distortion even after the lens is properly Note adjusted, especially at shorter throw distances. If this is the case, Vidikron

recommends that you slightly over-scan the image into the screen frame area to mask the distortion.

34

Vidikron Vision Model 15 Installation/Operation Manual

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Digital Light Processing DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Product Information Retain for Your Records Important Safety Instructions Compliance Information Declaration of ConformityFCC Part 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Specifications Table of Contents Xii 1List of Figures List of Figures Xiv 1Introduction About This ManualThis Manual Using This Manual If you need Turn toDescription, Features and Benefits Optional Accessories 2Controls and Functions Vision 15 at a GlanceVertical Lens Shift Dial Shifts the image up or down POWER/STANDBY Indicator Indicates power status as follows Vision 15 Rear PanelHorizontal Lens Shift Dial Shifts the image left or right Component Video RCA connectors DVI-I Analog/DigitalVision 15 Remote Control Vision 15 Remote ControlOn / OFF Source Selection ButtonsAspect Ratio Selection Buttons 169Cust ISF NTCursor Keys Exit3Installation Remote ControlAvailable Range of the Remote Control OperationQuick Setup Installation OverviewStep Procedure For Details, Refer to Installation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsThrow Ratios for the Vision 15 Series Throw Throw Range Throw RatioProjector Model MinimumCeiling Installation Floor InstallationPosition Shift Vertical Lens Shift Example onlyHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Vision Vision 15ETInstalling the Optional CineWide Lens Base Plate Installation Adjusting the Projector Mounting the VisionFloor Mounting Upright Ceiling Mounting InvertedConnector Panel Access Connections to the VisionHDMI/DVI Connections See Figure Hdmi or DVI Source HDMI/DVI Source ConnectionsDVI to VGA Adapter VGA to VGA Cable DVI to DVI Cable PersonalComputer 11. Component Video Connections DVD Player, VCR LaserDisc, Camcorder Etc 12. Composite and S-Video ConnectionsConnection To PC or Automation Control SystemTurning on the Power 14. Connecting the 12-Volt Trigger Output to Other EquipmentChanging the OSD Language Adjusting the Picture Orientation Primary Lens Adjustments Focus and ZoomFocus Ring Zoom Ring Focus ring Zoom ring Cause the projector to malfunction 16. Vertical and Horizontal Lens Shift ControlsInstalling and Adjusting the CineWide Anamorphic Lens Primary lens is perfectly centered on the screenAdjusting the Lens Height and Angle Using the On-Screen Menus 4OperationPicture Adjust InstallationSetup Source SelectPerform the adjustments in the order listed here Picture AdjustSource Select Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Operation Aspect Ratio Settings Aspect RatioLetterbox IntelliAspect Geometry of Projected Image Installation ItalianHorizontal Keystone Correction Vertical Keystone CorrectionOverscan Examples Information HdmiSetup Becomes increasingly fragile and prone to sudden failureISF DNR Refer to Digital Noise Reduction DNR onOperation Operation 5Maintenance and Troubleshooting Cleaning the Projector Cleaning the LensCleaning the Intake and Exhaust Vents Lamp Maintenance Lamp CautionsLamp Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Command Description ReplySerial Communications 7Specifications Vision 15 SpecificationsLimited Warranty Specifications are subject to change without noticeRegulatory Approvals Vision 15 Dimensions Vision 15 DimensionsVision 15ET Dimensions Vision 15ET DimensionsComputer Signal Compatibility Chart Computer Signal CompatibilityResolution Horizontal VerticalVideo Signal Compatibility Video Signal Compatibility ChartFreq Compatible Inputs Note Resolution VideoPage 020-0863-00 Rev. a January

Vision 15ET/CineWideTM, Vision 15ET, Vision 15 specifications

The Vidikron Vision 15ET/CineWideTM, along with the Vision 15 and Vision 15ET models, represents a significant advancement in the realm of high-end home theater projection systems. Designed for cinema enthusiasts and home theater aficionados, these projectors provide an unparalleled viewing experience characterized by stunning visuals and a rich array of features.

At the core of the Vidikron Vision 15ET/CineWideTM is its advanced DLP technology, which delivers exceptional brightness and contrast. This ensures vibrant colors and deep blacks, which are essential for creating a cinematic atmosphere at home. The inclusion of CineWideTM technology further enhances this experience by employing a custom-designed lens that expands the image's width, reducing the presence of letterbox bars. This feature is particularly appreciated in widescreen content, providing a more immersive viewing experience.

Another notable feature of the Vision 15ET/CineWideTM is its high-resolution capability. With support for 1080p and capable of handling various video formats, the projector is versatile enough to accommodate a range of media sources, from Blu-ray players to gaming consoles. The projector’s aggressive pixel-shifting technology allows for effective upscaling of lower-resolution sources, ensuring that every detail is rendered with clarity.

The Vision 15 model stands out due to its user-friendly interface and installation flexibility. With multiple inputs including HDMI, component, and composite connections, it can seamlessly integrate with existing AV systems. Additionally, its lens shift and zoom capabilities provide installers with greater flexibility, allowing for optimal placement in any home theater environment.

Another advantage of the Vidikron projectors is their robust build quality. These models are designed to withstand the rigors of daily use while providing consistent performance over the years. Their cooling systems are also engineered to operate quietly, maintaining the immersiveness of the viewing experience without distracting noise.

Overall, the Vidikron Vision 15ET/CineWideTM, along with the Vision 15 and Vision 15ET projectors, offer an elite level of performance and versatility. With their advanced technologies, exceptional image quality, and user-centric design, they stand out as top choices for those looking to transform their home viewing experience into a true cinematic adventure. Whether for movie nights, gaming, or superb sports viewing, these projectors are engineered to impress.
Top Page Image Contents