Vidikron Vision 15ET/CineWideTM operation manual Lamp Replacement

Page 70

Maintenance and Troubleshooting

5.6

Lamp Replacement

1.Turn off the projector and wait for the cooling fan to stop.

2.Unplug the power cord. Allow the projector to cool down for approximately one hour prior to removing the lamp assembly for replacement.

3.Loosen the two captive

lamp cover screws and remove the cover.

4.Loosen the four lamp assembly mounting screws.

5.Grasp the lamp assembly

handle and pull gently, removing the lamp module from the projector housing. As you do so, the lamp cooling interlock switch on the inside of the lamp cavity (near the top) moves to the OFF position.

6.Gently slide the new lamp assembly into the lamp cavity. Align the two power connectors at the top of the lamp assembly with the two sockets at the top of the lamp cavity. Press gently on both sides of the lamp assembly to snap it into place. As you do so, the lamp cooling interlock switch returns to the ON position.

7.Tighten the lamp assembly mounting screws.

8.Replace the lamp cover and secure the captive lamp cover screws.

9.Plug in the projector and turn it on.

10.Reset the Lamp Timer to zero. To do this, select Lamp Reset from the Setup menu and press ENTER. The Vision 15 shows the number of hours the projector lamp has been in service and asks you to confirm or cancel the reset. Press ENTER again to confirm.

56

Vidikron Vision Model 15 Installation/Operation Manual

Page 69 Page 71
Image 70
Page 69 Page 71
Contents Digital Light Processing DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Product Information Retain for Your Records Important Safety Instructions Compliance Information Declaration of ConformityFCC Part 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Specifications Table of Contents Xii 1List of Figures List of Figures Xiv About This Manual 1IntroductionThis Manual Using This Manual If you need Turn toDescription, Features and Benefits Optional Accessories Vision 15 at a Glance 2Controls and FunctionsVertical Lens Shift Dial Shifts the image up or down Vision 15 Rear Panel POWER/STANDBY Indicator Indicates power status as followsHorizontal Lens Shift Dial Shifts the image left or right Component Video RCA connectors DVI-I Analog/DigitalVision 15 Remote Control Vision 15 Remote ControlAspect Ratio Selection Buttons On / OFFSource Selection Buttons 169Cursor Keys CustISF NT Exit3Installation Remote ControlAvailable Range of the Remote Control OperationInstallation Overview Quick SetupStep Procedure For Details, Refer to Installation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsProjector Model Throw Ratios for the Vision 15 SeriesThrow Throw Range Throw Ratio MinimumFloor Installation Ceiling InstallationPosition Shift Vertical Lens Shift Example onlyHorizontal Lens Shift Example only Vertical and Horizontal Lens Shift Limits Vision Vision 15ETInstalling the Optional CineWide Lens Base Plate Installation Floor Mounting Upright Adjusting the ProjectorMounting the Vision Ceiling Mounting InvertedConnections to the Vision Connector Panel AccessHDMI/DVI Connections See Figure Hdmi or DVI Source HDMI/DVI Source ConnectionsPersonal DVI to VGA Adapter VGA to VGA Cable DVI to DVI CableComputer 11. Component Video Connections DVD Player, VCR LaserDisc, Camcorder Etc 12. Composite and S-Video ConnectionsConnection To PC or Automation Control SystemTurning on the Power 14. Connecting the 12-Volt Trigger Output to Other EquipmentChanging the OSD Language Adjusting the Picture Orientation Focus and Zoom Primary Lens AdjustmentsFocus Ring Zoom Ring Focus ring Zoom ring Cause the projector to malfunction 16. Vertical and Horizontal Lens Shift ControlsInstalling and Adjusting the CineWide Anamorphic Lens Primary lens is perfectly centered on the screenAdjusting the Lens Height and Angle Using the On-Screen Menus 4OperationSetup Picture AdjustInstallation Source SelectPicture Adjust Perform the adjustments in the order listed hereSource Select Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Operation Aspect Ratio Settings Aspect RatioLetterbox IntelliAspect Geometry of Projected Image Installation ItalianHorizontal Keystone Correction Vertical Keystone CorrectionOverscan Examples Information HdmiSetup Becomes increasingly fragile and prone to sudden failureISF DNR Refer to Digital Noise Reduction DNR onOperation Operation 5Maintenance and Troubleshooting Cleaning the Projector Cleaning the LensCleaning the Intake and Exhaust Vents Lamp Maintenance Lamp CautionsLamp Replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Command Description ReplySerial Communications 7Specifications Vision 15 SpecificationsSpecifications are subject to change without notice Limited WarrantyRegulatory Approvals Vision 15 Dimensions Vision 15 DimensionsVision 15ET Dimensions Vision 15ET DimensionsResolution Computer Signal Compatibility ChartComputer Signal Compatibility Horizontal VerticalFreq Compatible Inputs Note Resolution Video Signal CompatibilityVideo Signal Compatibility Chart VideoPage 020-0863-00 Rev. a January

Vision 15ET/CineWideTM, Vision 15ET, Vision 15 specifications

The Vidikron Vision 15ET/CineWideTM, along with the Vision 15 and Vision 15ET models, represents a significant advancement in the realm of high-end home theater projection systems. Designed for cinema enthusiasts and home theater aficionados, these projectors provide an unparalleled viewing experience characterized by stunning visuals and a rich array of features.

At the core of the Vidikron Vision 15ET/CineWideTM is its advanced DLP technology, which delivers exceptional brightness and contrast. This ensures vibrant colors and deep blacks, which are essential for creating a cinematic atmosphere at home. The inclusion of CineWideTM technology further enhances this experience by employing a custom-designed lens that expands the image's width, reducing the presence of letterbox bars. This feature is particularly appreciated in widescreen content, providing a more immersive viewing experience.

Another notable feature of the Vision 15ET/CineWideTM is its high-resolution capability. With support for 1080p and capable of handling various video formats, the projector is versatile enough to accommodate a range of media sources, from Blu-ray players to gaming consoles. The projector’s aggressive pixel-shifting technology allows for effective upscaling of lower-resolution sources, ensuring that every detail is rendered with clarity.

The Vision 15 model stands out due to its user-friendly interface and installation flexibility. With multiple inputs including HDMI, component, and composite connections, it can seamlessly integrate with existing AV systems. Additionally, its lens shift and zoom capabilities provide installers with greater flexibility, allowing for optimal placement in any home theater environment.

Another advantage of the Vidikron projectors is their robust build quality. These models are designed to withstand the rigors of daily use while providing consistent performance over the years. Their cooling systems are also engineered to operate quietly, maintaining the immersiveness of the viewing experience without distracting noise.

Overall, the Vidikron Vision 15ET/CineWideTM, along with the Vision 15 and Vision 15ET projectors, offer an elite level of performance and versatility. With their advanced technologies, exceptional image quality, and user-centric design, they stand out as top choices for those looking to transform their home viewing experience into a true cinematic adventure. Whether for movie nights, gaming, or superb sports viewing, these projectors are engineered to impress.
Top Page Image Contents