Vidikron v120 manual Gain/Offset Refer to ISF Night Display Color, above

Page 72

Operation

ISF Night - Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but adjust the color balance of the incoming signal. These settings are also saved independently for each input.

•Gain/Offset: Refer to ISF Night - Display Color, above.

•Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a Composite, S-Video or Component video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them.

•Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

ISF Day - Display Color: Refer to ISF Night - Display Color.

ISF Day - Input Image: Refer to ISF Night - Input Image.

ISF Day - Input Color: Refer to ISF Night - Input Color.

Save ISF Settings: Whenever you make a change to the ISF settings, you should always save it. Select Save ISF Settings from the ISF Calibration menu to do this. In the event you ever have to perform a System Reset, you can restore the saved ISF settings by selecting Restore Saved Settings in the Service menu. (System Reset and Restore Saved Settings are described on page 62.)

Output Shift: The controls in the Output Shift menu are similar to those in the Input Position menu, except that they change the characteristics of the output signal. These settings are saved independently for each aspect ratio.

Splash Timer: Select Splash Timer from the Calibration menu to set the amount of time the Vidikron/ISF logo “splash” screen appears when you turn on the projector. The range is from 5 to 60 seconds, in one-second increments.

OSD Position: To adjust the menu and press ENTER (or

position of the OSD, select OSD Position from the Calibration SELECT).

Press or to select “Hor.” or “Ver.” Then, press or change the position.

60

Vidikron Vision Model 120 Owner’s Operating Manual

Page 71 Page 73
Image 72
Page 71 Page 73
Contents 120 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting OperationSerial Communications Table of Contents 1List of Figures List of Figures Xii 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Vision 120 offers these key features and benefitsOptional Accessories Controls and Functions Vision 120 at a GlanceVision 120 Rear Panel Vision 120 Rear PanelUSB-B DVI-DL Dual-LinkVHD Controller Front Panel VHD Controller Front PanelIssue LED Service only For future use VHD Controller Rear PanelDVI-DL DUAL-LINK Output 1080p RS-232/485 Control PortHdmi I 1 / Hdmi II 2 Digital 10. HD3 InputVision 120 Remote Control Vision 120 Remote ControlPicture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-VideoMemory Preset Buttons Aspect Ratio Selection Buttons169 Lbox Letterbox3Installation Remote ControlOperation Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 120/CineWide or VisionInstallation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsVision 120 Lens Options and Throw Ratios Ceiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Vision 120 Vertical and Horizontal Lens Shift Limits Folded OpticsInstalling the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 120/CineWide with AutoScope motor assembly Remove Vision 120 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 120/CineWide Adjusting the Projection Mounting the VisionFloor Mounting Upright Ceiling Mounting Inverted AngleConnector Panel Access Connecting the VHDConnections to the Vision 120 and VHD Controller Connecting Source ControllerHdmi Connections See Figure Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with12. Digital DTV RGB or Component Video Connections HD1, HD2 13. Digital DTV RGB or Component Video Connections HD3 Analog Computer RGB Connections See Figure 14. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 16. RS-232 Control System ConnectionConnecting 12-Volt Trigger EquipmentConnecting an External IR Receiver to the VHD Controller VHD ControllerRear Panel Turning on the Power Adjusting the Picture OrientationPower source Primary Lens Adjustments FocusZoom Installing and Adjusting the CineWide Anamorphic Lens Plate fixed CineWide20. Attaching the Anamorphic Lens to the Lens Adapter Ring Too Far Left Correct position Too Far Right Installation Anamorphic Lens Top View Adjusting the Geometry Installation Using the On-Screen Menus 4OperationISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Aspect Ratio Settings Description169 Hdtv programs in their nativePicture PicturePerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionISF Presets ISF PresetsInformation InformationCalibration Calibration ISF NightISF Day OSD Position To adjust the menu and press Enter or Gain/Offset Refer to ISF Night Display Color, aboveService ServiceHD Format Presets 5Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port Configuration6Serial Communications Serial Commands and Responses Command Description ResponseInput Selection Commands Aspect Ratio CommandsCommand Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select buttonSerial Communications 7Specifications Vision 120 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsVHD Controller Specifications Vision 120 Dimensions Vision 120/CineWide with AutoScope DimensionsPage Vidikron

v120 specifications

The Vidikron V120 is a high-performance video projector that has carved a niche for itself among enthusiasts seeking exceptional home theater experiences. Known for its advanced technologies and impressive specifications, the V120 is designed to deliver stunning visuals and immersive sound, making it an ideal choice for both casual viewers and serious cinephiles.

One of the standout features of the Vidikron V120 is its superior resolution. Sporting a native 1080p (1920x1080) resolution, it ensures that every detail in your favorite movies and shows is displayed with razor-sharp clarity. This full HD resolution is complemented by its ability to upscale lower-resolution content, providing a better viewing experience regardless of the source material.

The projector employs advanced Liquid Crystal on Silicon (LCoS) technology, which combines the benefits of both LCD and DLP technologies. This enables the V120 to produce vibrant colors and deep blacks, resulting in lifelike images that truly capture the viewer's attention. The contrast ratio is particularly impressive, allowing for greater depth in dark scenes without losing detail.

Another key characteristic is its brightness capability, which is rated at an impressive 1200 ANSI lumens. This ensures that the V120 can perform admirably in various lighting conditions, making it suitable for both dedicated home theaters and multi-purpose rooms. The brightness can be adjusted to suit personal preferences or ambient light levels, enhancing the viewing experience further.

The Vidikron V120 also features a wide range of connectivity options, including HDMI, VGA, and component inputs. This versatility allows users to connect multiple devices, such as Blu-ray players, gaming consoles, and streaming devices, without the hassle of constantly changing cables. The inclusion of analog audio inputs and outputs ensures compatibility with a variety of sound systems, enhancing the overall home entertainment experience.

In terms of installation, the V120 offers both vertical and horizontal lens shift capabilities, along with zoom functionality. This flexibility makes it easier to achieve the perfect image alignment, regardless of your room's setup. The projector is designed for quiet operation, reducing distractions and allowing viewers to fully immerse themselves in the content.

Overall, the Vidikron V120 combines cutting-edge technology with thoughtful design elements to create a projector that delivers exceptional performance for movie lovers and home theater aficionados. With its stunning image quality, versatile connectivity, and user-friendly installation features, the V120 stands out as a top choice in the competitive projector market.
Top Page Image Contents