Vidikron v120 manual Issue LED

Page 21

Controls and Functions

6.RIGHT BUTTON

Used to direct-select inputs or move the menu cursor right in the OSD. When no menu is present on-screen, the RIGHT button toggles through the different sources, in this order: Composite (VID) - S-Video - HD 1 (RCA) - HD 2 (BNC) - HD 3 (VGA/Y-Pb-Pr) - HDMI 1 - HDMI 2

7.MENU BUTTON

Pressing the MENU button brings up the main menu. Also, if you are in an adjustment mode or function, pressing MENU brings the menu back one level.

8. RUN LED

–Lights blue to indicate that the projector is functioning normally.

–Flashes blue (one second on/one second off) to indicate an error condition.

–Flashes blue (one half-second on/one half-second off) for approximately 90 seconds after the system is turned off.

9.ISSUE LED

Lights red to indicate an error condition.

10.UP BUTTON

Use to direct-select aspect ratios or move the menu cursor up in the OSD. When no menu is present on-screen, the UP button toggles through aspect ratios in the following order:

16:9 - 4:3 - Letterbox - IntelliWide - Cinema - IntelliWide 2.35

(IntelliWide 2.35 is available only on CineWide-equipped projectors. For more information about aspect ratios, refer to Table 4-1.)

11.SELECT BUTTON

Press SELECT to confirm your selection of a highlighted choice on the OSD.

12.STAND-BY LED

Lights orange to indicate that the projector is in standby mode.

13.SOFT POWER BUTTON

Press once to turn on the Vision 120. Press it again to put the projector into Standby mode. For a discrete on or off command, you can use the direct access buttons on the remote control (see Figure 2-5).

Vidikron Vision Model 120 Owner’s Operating Manual

9

Image 21

Contents

120 Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Maintenance and TroubleshootingSerial Communications Table of Contents 1List of Figures List of Figures Xii About This Manual 1IntroductionIf you need Turn to Using This ManualVision 120 offers these key features and benefits Description, Features and BenefitsOptional Accessories Vision 120 at a Glance Controls and FunctionsVision 120 Rear Panel Vision 120 Rear PanelDVI-DL Dual-Link USB-BVHD Controller Front Panel VHD Controller Front PanelIssue LED VHD Controller Rear Panel Service only For future useDVI-DL DUAL-LINK Output 1080p RS-232/485 Control Port10. HD3 Input Hdmi I 1 / Hdmi II 2 DigitalVision 120 Remote Control Vision 120 Remote ControlOn / OFF Picture Adjustment Buttons BRT BrightnessSource Selection Buttons VID S-VideoAspect Ratio Selection Buttons Memory Preset Buttons169 Lbox Letterbox3Installation Remote ControlOperation Installation Overview Quick SetupStep Procedure For Details, Refer to If installing a Vision 120/CineWide or VisionProjector Installation Options Installation ConsiderationsInstallation Type Advantages ConsiderationsVision 120 Lens Options and Throw Ratios Floor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Vision 120 Vertical and Horizontal Lens Shift LimitsInstalling the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 120/CineWide with AutoScope motor assembly Remove Vision 120 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 120/CineWide Mounting the Vision Adjusting the ProjectionFloor Mounting Upright Ceiling Mounting Inverted AngleConnector Panel Access Connecting the VHDConnections to the Vision 120 and VHD Controller Controller Connecting SourceHdmi Connections See Figure Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with12. Digital DTV RGB or Component Video Connections HD1, HD2 13. Digital DTV RGB or Component Video Connections HD3 14. Analog RGB Connections Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Video/Composite Video Connections See Figure16. RS-232 Control System Connection ConnectionEquipment Connecting 12-Volt TriggerConnecting an External IR Receiver to the VHD Controller VHD ControllerRear Panel Turning on the Power Adjusting the Picture OrientationPower source Primary Lens Adjustments FocusZoom Plate fixed CineWide Installing and Adjusting the CineWide Anamorphic Lens20. Attaching the Anamorphic Lens to the Lens Adapter Ring Too Far Left Correct position Too Far Right Installation Anamorphic Lens Top View Adjusting the Geometry Installation 4Operation Using the On-Screen MenusService ISF PresetsInput Source Aspect RatioMain Menu Input SourceAspect Ratio Description Aspect Ratio Settings169 Hdtv programs in their nativePicture PictureTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionISF Presets ISF PresetsInformation InformationCalibration Calibration ISF NightISF Day Gain/Offset Refer to ISF Night Display Color, above OSD Position To adjust the menu and press Enter orService ServiceHD Format Presets Lamp Replacement 5Maintenance and TroubleshootingFilter Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port Configuration6Serial Communications Command Description Response Serial Commands and ResponsesInput Selection Commands Aspect Ratio CommandsMenu Navigation Commands Command Description Response Image Preset CommandsPicture Adjust Commands Enter or Select buttonSerial Communications Vision 120 Specifications 7SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsVHD Controller Specifications Vision 120/CineWide with AutoScope Dimensions Vision 120 DimensionsPage Vidikron