AMD GA-K8N51GMF-RH user manual Integrated Peripherals

Page 35

2-3	Integrated Peripherals

		CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
			Integrated Peripherals
`	SATAII RAID Config		[Press Enter]		Item Help
	On-Chip IDE Channel0		[Enabled]		Menu Level`
	On-Chip IDE Channel1		[Enabled]
	IDE1 Conductor Cable		[Auto]
	IDE2 Conductor Cable		[Auto]
	Serial-ATA-II 1		[Enabled]
	On-Chip USB		[V1.1+V2.0]
	USB Keyboard Support		[Disabled]
	USB Mouse Support		[Disabled]
	Onboard Audio Function		[Auto]
	Onboard LAN Function		[Auto]
	Onboard LAN Boot ROM		[Disabled]
	Onboard 1394 Function		[Enabled]
	Onboard Serial Port 1		[3F8/IRQ4]
	Onboard Serial Port 2		[2F8/IRQ3]
	Onboard Parallel Port		[378/IRQ7]
	Parallel Port Mode		[SPP]
KLJI: Move		Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
		F5: Previous Values		F7: Optimized Defaults

SATAII RAID Config
		CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
			SATAII RAID Config
	SATA-II RAID function		[Disabled]		Item Help
x SATA-II 1 Primary RAID			Disabled		Menu Level`
x SATA-II 1 Secondary RAID			Disabled
KLJI: Move		Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values		F6: Fail-Safe Defaults		F7: Optimized Defaults
	SATA-II RAID function
	Enabled	Enable SATAII RAID function.
	Disabled	Disable SATAII RAID function. (Default value)
	SATA-II 1 Primary RAID
	Enabled	Enable SATAII 1 1st SATA RAID function.
	Disabled	Disable this function. (Default value)
	SATA-II 1 Secondary RAID
	Enabled	Enable SATAII 1 2nd SATA RAID function.
	Disabled	Disable this function. (Default value)

English

- 35 -

BIOS Setup

Image 35

Contents GA-K8N51GMF/ GA-K8N51GMF-RH Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-K8N51GMF/GA-K8N51GMF-RH Motherboard Layout Block Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature Summary4Mbit flash ROM Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out Rear Speaker OutATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII0 Sata 3Gb/s Connector IDE1 / IDE2 IDE ConnectorFpanel Front Panel Jumper Faudio Front Audio Panel ConnectorUSB1 / FUSB2 Front USB Connector Cdin CD In ConnectorCI Chassis Intrusion, Case Open PowerledClrcmos Clear Cmos BatterySpdifio Spdif In/Out 16 F11394 Ieee 1394 ConnectorEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F4„ PnP/PCI Configuration „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupIDE Channel 0 Master, Slave, IDE Channel 1 Master, Slave TimeHalt on Floppy 3 Mode Support for Japan AreaIDE Channel 2/3 Master Drive a Total Memory Memory Base Memory Extended MemoryBoot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Onboard GPU Password CheckInit Display First Frame Buffer SizeIntegrated Peripherals IDE1 Conductor Cable Onboard LAN Boot ROMOn-Chip IDE Channel0 On-Chip IDE Channel1Onboard Parallel Port Parallel Port ModeOnboard 1394 Function Onboard Serial PortUSB Resume from Suspend Power-On by AlarmPME Event Wake Up Modem Ring OnAC Back Function Power On By KeyboardKB Power on Password Power On By MousePCI 2 IRQ Assignment PnP/PCI ConfigurationsPCI 1 IRQ Assignment CPU Smart FAN Control Note Current VoltageV Vcore / DDR Power / +3.3V / +12VSystem/CPU Temperature System/CPU FAN Speed RPMDimm OverVoltage Control CPU FrequencyPcie Clock K8 CPU Clock RatioRobust Graphics Booster Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionSystem requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish Before you begin SPP SCSI-0 Nvidia Mirror Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES English Nvidia Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Solutions Configuring a bootable RAID array with Microsoft WindowsYES English 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English Step Troubleshooting English English English Taiwan Headquarters Contact UsGigabyte Global Service System